background image

Page 17

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RECOMMENDED REPLACEMENT PARTS AND CHANGE INTERVALS:

Note:  Depending on incoming feed water conditions replacement time frame may vary.

Description 

 

 

     Part #            

        Change time Frame

Sediment Filter, 5 Micron, 9 7/8”: 

#FPMB5-978 

 

6 Months   

Carbon Block, 5 Micron, 9 3/4”:   

#WCBCS975 

 

6 Months   

In-line Carbon Filter:   

 

#AICRO   

 

12 Months  

TFC Membrane, 50GPD @60PSI: 

#W-1812-50 

 

2 to 5 years 

Depending on water chemistry, water temperature, and water pressure Watts R.O. Systems production and performance will vary.

Efficiency rating means the percentage of the influent water to the system that is available to the user as reverse osmosis treated water under

operating conditions that approximate typical daily usage. Recovery rating means the percentage of the influent water to the membrane portion of 

the system that is available to the user as reverse osmosis treated water when the system is operated without a storage tank or when the storage 

tank is bypassed. There is an average of 4 gallons of reject water for every 1 gallon of product water produced.

REFER TO OWNER’S INSTALLATION/SERVICE MANUAL FOR FURTHER MAINTENANCE REQUIREMENTS AND WARRANTY INFORMATION.

Phone: 800-659-8400                                          Fax: 800-659-8402                                              www.watts.com

GENERAL USE CONDITIONS:

1. System to be used with municipal or well water sources treated and tested on regular basis to insure bacteriological safe quality.  DO NOT use with water that 

is micro biologically unsafe or unknown quality without adequate disinfection before and after the system.  Systems certified for cyst reduction may be used on 

disinfected water that may contain filterable cysts.

2. Operating Temperature: 

 

 

Maximum: 100°F (40.5°C) 

 

 

Minimum: 40° (4.4°)

3. Operating Water Pressure: 

 

 

Maximum: 100 psi (7.0kg/cm2)   

 

Minimum: 40 psi (2.8kg/cm2)

4. pH 

 

 

 

 

2 to 11

5. Maximum iron present in incoming feed water supply must be less than 0.2 ppm.

6. Hardness of more than 10 grains per gallon (170 ppm) may reduce membrane life expectancy.

7. Recommend TDS (Total Dissolved Solids) not to exceed 1800 ppm.

Watts Water Technologies

 1725 W. Williams Drive C-20

Phoenix, AZ 85027 USA

GTS450S / GTS550S

 

Avg. In. 

Avg. Eff. 

% Reduction  pH 

Pressure 

Max Eff. 

Inf. challenge 

Max Allowable

 

(mg/L) 

(mg/L) 

 

 

 

mg/L 

concentration 

concentration

 

 

 

 

 

 

 

mg/L 

mg/L

Bacteria* 

 

 

99.9999% 

 

 

 

 

   

Virus* 

 

 

99.99%

Arsenic (Pentavalent) 

334.62 ug/L 

5.039 ug/L 

98.4% 

 

50psi 

19 ug/L 

   0.30±10% 

   0.010 mg/L

Barium Reduction 

10.2 

0.13 

98.7% 

7.24 

50psi 

0.27 

   10.0±10% 

    2.0

Cadmium Reduction 

0.031 

0.0001 

99.7% 

7.49 

50psi 

0.0009 

    0.03±10% 

    0005

Chromium (Hexavalent) 

0.30 

0.006 

98.0% 

7.24 

50psi 

0.013 

    0.03±10% 

    0.1

Chromium (Trivalent) 

0.30 

0.003 

99.0% 

7.24 

50psi 

0.008 

    0.03±10% 

    0.1

Copper Reduction 

3.0 

0.04 

98.7% 

7.64 

50psi 

0.06 

    3.0±10% 

    1.3

Cysts 

222,077#/ml 

10 #/ml 

99.99% 

 

50psi 

58      minimum 50,000/mL 

     N/A 

Fluoride Reduction 

8.0 

0.33 

95.9% 

7.49 

50psi

 

0.47 

    8.0±10% 

    1.5    

Lead Reduction 

0.15 

0.004 

97.3% 

7.49 

50psi 

0.008 

    0.15±10% 

    0.0107

Nitrite and Nitrate 

29.2 

6.6 

77.3% 

7.64 

50psi 

10.0 

    3.0±10% 

    10.0

Nitrate Reduction 

26.3 

6.1 

76.8% 

7.64 

50psi 

10.0 

    3.0±10% 

    10.0

Nitrite Reduction 

2.8 

0.5 

82.1% 

7.64 

50psi 

0.77 

    3.0±10% 

    1.0

Perchlorate 

0.10 

0.003 

96.5% 

7.39 

50 psi 

0.005 mg/L 

0.10±10% 

     0.006

Radium 226/228 

25pCi/L 

5pCi/L 

80.0% 

7.24 

50psi 

5pCi/L 

    25pCiL±10% 

    5pCiL

Selenium 

0.10 

<0.001 

99.0% 

 

50psi 

<0.001 

    0.10±10% 

    0.05

TDS 

764 

36 

95.2% 

7.84 

50psi 

50.0 

    750±40mg/L 

    187

Turbidity 

81 NTU 

0.15 NTU 

99.8% 

 

50psi 

0.28 NTU 

    11±1 NTU 

    0.5 NTU

              Recovery - 16.34% 

 

 Daily Production Rate - 17.32 GPD 

 

Efficiency - 8.91%

*independantly tested and verified by Bio Vir Laboratories

Summary of Contents for GTS450S





















Reviews: