background image

 

2

 

ES-A-ACV-LF985GD  2115 

© 2021 Watts

Deep Well Pump Control Valve

Full Port Ductile Iron Dual Chamber Valve
Features

•  Installed on branch of tee off main pumping header
•  Normally open construction
•  Discharges to atmosphere on pump start-up
•  Closes slowly diverting pressure into system during pumping 

cycle

•  Opens slowly on pump shut-off
•  Limit Switch turns pump off when valve is fully open
•  Adjustable Opening and Closing Speed
•  Solenoid equipped with Manual Operator

1

3

4

2(L)

CLOSES VALVE

OPENS VALVE

FLOW

5

X

X

X/Y

(Supply Pressure)

Engineering Specification

Standard Components

Options and Accessories

 

{

L – Dual Limit Switch

1 – Main Valve (900GD - Dual Chamber)
2 – Limit Switch 
3 – 4-Way Solenoid 
4 – Adjustable Opening Speed
5 – Adjustable Closing Speed
Y – Y-Strainer
X – Isolation Cocks 

LEAD FREE

*

The information contained herein is not intended to replace the full 

product installation and safety information available or the experi-

ence of a trained product installer. You are required to thoroughly 

read all installation instructions and product safety information 

before beginning the installation of this product. 

NOTICE

* The wetted surface of this product contacted by consumable water 

contains less than 0.25% of lead by weight.

Operation

The Deep Well Pump Control Valve is designed to minimize the 

surges associated with the starting and stopping of well pumps. 

The valve slowly opens and closes as required to control pumping 

related surges. The pump starts and stops against an open valve.

Pump start up:

 When the pump is signaled to start, the 4-Way 

Solenoid is energized and directs fluid and pressure into the cover 

chamber (above the diaphragm), and relieves fluid and pressure 

from the power chamber (below the diaphragm). The fluid and 

pressure relieved from the cover chamber is vented to atmo-

sphere or available floor drain. The valve closes at an adjustable 

rate, gradually admitting pumping pressure into the distribution 

system. Rate of valve closure is controlled by the adjustable clos-

ing speed control, which restricts the speed at which fluid and 

pressure evacuate the power chamber. The valve remains closed 

during the pumping cycle.

Pump shutdown:

 When the pump is signaled to shut-off, the 

4-Way Solenoid is de-energized, and directs fluid and pressure 

into the power chamber (below the diaphragm), and relieves fluid 

and pressure from the cover chamber (above the diaphragm). The 

fluid and pressure relieved from the cover chamber is vented to 

atmosphere or available floor drain. The valve opens at an adjust-

able rate, gradually reducing pumping pressure, allowing the 

system check valve to slowly close. Rate of valve opening is con-

trolled by the adjustable opening speed control, which restricts 

the speed at which fluid and pressure evacuate the cover cham-

ber. When the valve reaches the full open position, the limit switch 

is actuated, turning the pump off.

Manual Operation:

 Engaging the Solenoid Manual operator 

simulates power to the solenoid, manually closing the main valve. 

Disengaging the Solenoid Manual operator returns the valve to 

the open position.

Series LF985GD

Summary of Contents for AMES LF985GD Series




















Reviews: