6
Visit our website at http://watt-age.globalhobby.com or for Customer Service at http://globalservices.globalhobby.com
Here's a List of What We Used to Finish Our MiG-15 EDF:
IMPORTANT
The part numbers listed for the Hitec receiver, Cirrus servos, Cirrus Y-Harness and Hitec servo extension are
compatible with Hitec and JR (receiver is compatible with Hitec only) radio control systems. These items are also available with
connectors that are compatible with Futaba and Airtronics radio control systems. (Micro 555 receiver is also available for Airtronics,
Futaba and JR radio systems.) The Wattage IC-30A ESC is compatible with Futaba, JR, Hitec and Airtronics Z.
When you purchase the Hitec Micro 555 receiver, you must also purchase a Hitec brand crystal compatible with the receiver. The
crystal must also be on the same frequency as your transmitter. Note that the Micro 555 receiver uses a dual conversion FM
Hitec crystal.
QTY. 1 759118
Hitec Micro 555 5Ch. Receiver
Hitec Dual Conversion FM RX Crystal
QTY. 3 444052
Cirrus CS-10 Super-Micro Servos
QTY. 1 444728
Cirrus Y-Harness
QTY. 1 128486
Wattage IC-30A Micro ESC
QTY. 1 128552
Wattage 10 Cell 1100Mah 2/3A NiMH Flight Battery
QTY. 1 130108
Wattage PF-12 AC/DC Park Flyer Charger
QTY. 1 131175
Wattage 14 Gauge Silicon Motor Wire
QTY. 1 625085
Deans Ultra-Plug Connector
3M 3/4" Wide Clear Plastic Tape - Available at Most Hardware Stores
OUR RECOMMENDATIONS, CONTINUED....
If you want to utilize the optional nose gear steering, you'll also need these items:
QTY. 1 444052
Cirrus CS-10 Super-Micro Servo
QTY. 1 759637
Hitec 6" Servo Extension
Note:
If you're wondering why we've recommended
using 14 gauge silicon motor wire and a Dean's
Ultra-Plug connector, please read the special tips
we've provided on page # 5. These two items are just
as important as a good ESC and flight battery.
❑
Kwik Bond 5 Minute Epoxy # 887560
❑
Pacer Z-42 Threadlocker # 339162
❑
# 0 Phillips Head Screwdriver
❑
# 1 Phillips Head Screwdriver
❑
.050 Hex Wrench
❑
Magnum Z-Bend Pliers # 237473
❑
Wire Cutters
❑
Needle Nose Pliers
❑
Adjustable Wrench
❑
Excel Modeling Knife # 692801
❑
Scissors
❑
Electric or Hand Drill
❑
Assorted Drill Bits
❑
Ruler
❑
Pencil
❑
220 Grit Sandpaper w/Sanding Block
❑
Paper Towels
❑
Rubbing Alcohol
❑
NHP Epoxy Mixing Sticks # 864204
❑
NHP Epoxy Mixing Cups # 864205
❑
K&S 30 Watt Soldering Iron # 598120
❑
Solder
❑
Heat-Shrink Tubing (Assorted Sizes)
❑
Prather Prop Balancer # 520429 (Optional)
SECTION 2: TOOLS AND SUPPLIES REQUIRED
The tools and supplies listed below will be necessary to finish the assembly of your MiG-15 EDF. We suggest having these
items onhand before beginning assembly.