background image

11

Product use and decontamination declaration

In compliance with the UK Health & Safety at Work Act and the Control of Substances Hazardous to Health
Regulations
 you, the user are required to declare the substances which have been in contact with the product(s)
you are returning to Watson-Marlow or any of its subsidiaries or distributors. Failure to do so will cause delays in
servicing the product. Therefore, please complete this form to ensure that we have the information before receipt
of the product(s) being returned. A FURTHER COPY MUST BE ATTACHED TO THE OUTSIDE OF THE PACKAG-
ING CONTAINING THE PRODUCT(S)
You, the user, are responsible for cleaning and decontaminating the
product(s) before returning them.

Please complete a separate Decontamination Certificate for each pump returned.
RGA No: .......................

1

Company

Address

........................................

Postcode ........................................

Telephone

........................................

Fax Number ....................................

3.4 Cleaning fluid to be used if residue of chemical is found during

2 Product

servicing;

2.1 Serial Number ................................

(a)

2.2 Has the Product been used?

(b) ……………………………………………

YES

     NO

(c) ……………………………………………

(d) ……………………………………………

If yes, please complete all the following

Sections

If no, please complete Section

5 only

3 Details of substances pumped

4  I hereby confirm that the only substances(s) that the equipment
specified has pumped or come into contact with are those named, that the
information given is correct, and the carrier has been informed if the

3.1 Chemical names:

consignment is of a hazardous nature.

(a) ....................................................... 5 Signed ……………………………………………….. ...........

(b) .......................................................

Name …………………………………………………

(c) .......................................................

Position ……………………………………………….

(d) .......................................................

Date …………………………………………………..

 3.2 Precautions to be taken in
handling these substances:

(a) ........................................................

(b) .......................................................................................................

(c) ........................................................

(d) ........................................................

3.3 Action to be taken in the event of human contact:

(a) ………………………………………………………………….

(b) ………………………………………………………………….

(c) ………….………………………………………………………

(d) ………….………………………………………………………

Watson-Marlow Limited   Falmouth   Cornwall   TR11 4RU   England   Tel: 01326 370370   Fax: 01326 376009

Note: To assist us in our servicing
please describe any fault condition you
have witnessed.

Summary of Contents for 621 Trio












Reviews: