Waterous CR Series Operation And Maintenance Instructions Download Page 3

F-1031, Section 2112 

Page 3 of 15 

 

 

Safety Information

 

 

 
 

Read through the safety information and operating instructions carefully before  
using your Waterous Fire Pump.

 

 
 

WARNING 

Hose Testing Hazard.  May result in serious personal injury. 

Due to a potential for catastrophic hose failure during service testing of fire hose, it is vital that safety precautions be taken 
to prevent exposure of anyone to this danger.  Fire pumps on fire department apparatus are not designed for and should 
not be used for service testing of fire hoses.  Hose testing machines should be used for service testing of fire hoses.  
 
 

WARNING 

Pressure Hazard.  May result in serious personal injury.

  

If a fire pump on a fire department apparatus is used for service testing of fire hoses, the procedures in NFPA 1962 

MUST 

be followed

 including the use of a fire department gate valve with a ¼-inch (6 mm) hole drilled through the gate installed 

between the fire apparatus discharge outlet and the hose test layout to prevent a volume surge from the pump in the event 
a hose bursts during testing.   
 
 

WARNING 

Scalding Water Hazard.  May result in serious burns.

 

If a fire pump on a fire department apparatus is used for service testing of fire hoses, pump discharge water must be 
circulated through a by-pass system or discharged through a slightly open discharge valve, or some other provision must 
be used to prevent overheating.  If the pump runs for a few minutes without adequate flow through the pump, water may be 
heated enough to scald someone when a valve is opened.     

 
 
 

Summary of Contents for CR Series
















Reviews: