Waterous CR Series Operation And Maintenance Instructions Download Page 1

 

CR/CRU-1/CRU-2 Series 

Operation and Maintenance Instructions 

 
 

 

Table of Contents 

 

Safety Information 

----------------------------------------------

 2, 3 

Introduction ......................................................................4 

General Description .........................................................4 

Components .....................................................................4 

Options .............................................................................4 

Available Models ..............................................................5 

Operating Instructions 

Pumping from Water Tank ............................................7 

Pumping from Hydrant or in Relay ...............................8 

Pumping from Draft ......................................................9 

Fire Hose Testing ....................................................... 10 

Lubrication 

CR Models .................................................................. 11 

CRU-1/CRU-2 Models .......................................... 12-14 

Mechanical Seal ......................................................... 15 

Overheat Protection Manager ....................................... 15 

 

 

 

 

 
 
 

 

 
 

 

 

 

 
 

 

 

 

 

Read through the installation 
instructions carefully before using 
your Waterous CR/CRU-1/CRU-2 Series Pump 

 

 

 
 
 
 

 

NOTE: Instructions subject to change without notice 

 

 

F-1031, Section 2112 (6/21/18) 

 

Waterous Company, 125 Hardman Avenue South, South St. Paul, Minnesota  55075  USA  (651) 450-5000 

www.waterousco.com

 

 

Summary of Contents for CR Series
















Reviews: