background image

 

infiniti

 Operating, Installation, and Service Manual                                                                     Page 54 - Revision: 9-15-2016 

WATERLOGIC MANUFACTURED WATER TREATMENT SYSTEM LIMITED WARRANTY 

UNITED STATES AND CANADA ONLY 

 

Waterlogic water treatment systems are guaranteed to the original purchaser to be free of defects in 

materials and workmanship for a period of three (3) years from the date of purchase, but in no event 

longer than forty-eight (48) months from the date of manufacture. Waterlogic Commercial Products, 

LLC (“Waterlogic”) based in the U.S.A. and its affiliated companies are not liable for any cost of 

removal, installation, transportation, or any other charges which may arise in connection with a 

warranty claim. 

 

This warranty does not cover damage or wear to products caused by abnormal operating conditions, 

accident, abuse, misuse, unauthorized or improper alteration or repair, damage caused by or 

resulting from shipping or accident, damage caused by hot water, freezing, flood, fire, or acts of God. 

The effects from chlorine corrosion, scaling and normal wear are specifically excluded from this 

warranty. This warranty does not cover products used outside the countries where the unit was 

purchased, and does not cover products that were not installed in accordance with Waterlogic printed 

installation and operating instructions obtained in training or from www.waterlogic.us. Failure to 

follow all instructions for operation and maintenance voids the warranty. This warranty is not 

transferable. 

 

To obtain warranty repairs or replacement, you must obtain a Return Authorization from Waterlogic. 

To obtain a Return Authorization, you must submit a Return Authorization form with supporting 

documentation to Waterlogic for evaluation. The form is available at www.waterlogic.us. Supporting 

documentation must include, but is not limited to; proof of purchase, installation date, failure date, 

and supporting installation and maintenance data.  After you submit a Return Authorization form and 

supporting documentation, Waterlogic will determine whether a reasonably apparent defect in 

materials or workmanship covered by this limited warranty exists. If Waterlogic determines the 

claimed defect is covered by this warranty, Waterlogic will, at its sole discretion, determine whether 

to correct the defect or replace the unit, free of charge to you. If Waterlogic determines that the unit 

should be returned for warranty service, Waterlogic will approve of return in writing and will issue a 

Return Authorization which you must obtain prior to shipping the product. You are responsible for the 

cost of freight in to Waterlogic. 

 

Waterlogic and its affiliated companies hereby limit the duration of any and all implied warranties to 

a maximum period of three (3) years from the date of purchase including, but not limited to, the 

implied warranties of merchantability and fitness for a particular purpose. Some states do not allow 

limitations on how long an implied warranty lasts, so the above limitation may not apply to you. 

Consequential and incidental damages are not recoverable under this warranty. Some states do not 

allow the exclusion or limitation of incidental or consequential damages, so the above limitation or 

exclusion may not apply to you. 

 

This warranty gives you specific legal rights and you may also have other rights which may vary from 

state to state. 

 

New Warranty Policy issued by Waterlogic Commercial Products LLC, USA - January 10, 2014 

 

Waterlogic Commercials Products LLC

             

Tel:  (800) 288-1891 

11710 Stonegate Circle                      Website:  waterlogic.us 

Omaha, NE  68164 

Summary of Contents for infiniti























































Reviews: