background image

19

 

Waterite carries a complete line of membrane cleaning agents, as well as a Clean-in-Place (CIP) 

system designed for easy cleaning of the membrane elements, without removing them from the 

housings. Contact your local representative or call Waterite for pricing and availability. Your RB8 

system is already pre-plumbed for a CIP connection. (Figure 3b on page 14) 

 

pH and permeate water 

The permeate water from a RO system generally has a lower pH than the feed water. This is caused 

by the processes removal of particles within the elements. It is strongly recommended that a pH 

balancing system be put in place to bring the pH back up to a neutral setting between 7.0 and 7.5.  

Consult with your water specialist or call 

Waterite

 for pH adjustment options and equipment. 

 

 

5.4 A Word on your warranty 

 

Keep your bill of sale and your warranty certificate, included in this kit.  This is needed to claim any 

parts or repair service during the warranty period.  Read the document completely for warranty claim 

instructions. 

Your RB8 BlackMaxx™ system comes with a limited one-year warranty covering materials and 

workmanship for one year from date of commissioning, subject to user’s compliance with these 

maintenance and operating instructions.  Membranes are excluded by the warranty and the seller’s 

responsibility is limited to any warranty carried by the original equipment manufacturer (OEM).  It is 

the purchaser’s responsibility to immediately notify Waterite in the event that defects are detected.  

Seller shall not be liable for any special, incidental or consequential damages and will at its option 

repair or replace any defective components.  Warranty excludes o-rings, membranes, pre-filter 

cartridges, freight charges, labour to remove or re-install equipment, use with feed water in excess 

of 2000 TDS, use of feed water that does not  meet recommended conditions or with system 

alterations made without a written approval from Waterite.  

 

 

Summary of Contents for BLACKMAXX RB8



























Reviews: