background image

Operation During A Power Failure 

In the event of a power failure, the valve will keep track of the time and day for 48 hours.  

The programmed settings are stored in a non-volatile memory and will not be lost during a 
power failure.  If power fails while the unit is in regeneration, the valve will finish regenera-

tion from the point it is at once power is restored.  If the valve misses a scheduled regen-
eration due to a power failure, it will queue a regeneration at the next regeneration time 

once power is restored. 

Main Display 

The main display will pause on the Date and Time page for 5 seconds.  Then it will continu-

ally scroll through all of the system diagnostic display pages.  To manually scroll through the 
diagnostics, press the down or up key.  To reset the TOTAL REGENS, TOTAL GALLONS 

OVER  RUN  TOTAL,  or  PEAK  flow  rates,  press  and  hold  the  MANUAL  REGEN  key  until  the 
value changes to zero. 

The brine tank is equipped with a safety float which prevents your brine tank from overfill-

ing as a result of a malfunction such as a power failure.  

Safety Float 

About The System 

PARAMETER

DESCRIPTION

JULY/17/2012

8:30

 

PM

TOTAL

 

1,500

 

GAL

REMAIN

 

1,200

 

GAL

PEOPLE

 

2

RESERVE

 

150

 

GAL

EST.

 

DAYS

 

TO

 

NEXT

REGEN

 

06

 

DAYS

LAST

 

REGEN

9/24/12

TOTAL

 

REGENS

10

TOTAL

 

GALLONS

001590

 

GAL

OVER

 

RUN

 

TOTAL

0500

 

GAL

CURRENT

 

1.5

 

GPM

PEAK

 

6.5

 

GPM

DELAYED

 

REGEN

OFF

REGEN

 

TIME

2:00

 

AM

REFILL

 

TIME

3:00

 

MIN

VALVE

 

MODE

SOFTENER

 

UF

TOTAL

 

4

 

DAYS

REMAIN

 

3

 

DAYS

Month,

 

Day,

 

Year,

 

Time

The

 

current

 

calculated

 

refill

 

time.

  

(Note:

  

The

 

refill

 

time

 

shown

 

will

 

be

 

reduced

 

by

 

the

 

pre

fill

 

%.

  

i.e.

 

If

 

pre

fill

 

%

 

is

 

70%,

 

then

 

displayed

 

refill

 

time

 

will

 

be

 

70%

 

of

 

the

 

full

 

target.)

The

 

current

 

setting

 

for

 

regeneration

 

time.

Number

 

of

 

people

 

in

 

the

 

household

 

and

 

the

 

calculated

 

reserve

 

capacity.

  

When

 

remaining

 

reaches

 

reserve

 

capacity

 

a

 

regeneration

 

will

 

be

 

scheduled.

The

 

number

 

of

 

days

 

remaining

 

before

 

regeneration.

  

This

 

option

 

is

 

only

 

in

 

filter

 

mode.

The

 

total

 

amount

 

is

 

the

 

system

 

capacity

 

when

 

fully

 

regenerated.

  

The

 

remaining

 

is

 

the

 

capacity

 

left

 

in

 

the

 

system.

The

 

estimated

 

number

 

of

 

days

 

until

 

the

 

next

 

regeneration

 

will

 

occur.

The

 

date

 

of

 

the

 

last

 

regeneration.

The

 

total

 

number

 

of

 

regenerations.

The

 

total

 

amount

 

of

 

gallons

 

treated

 

by

 

the

 

system.

The

 

total

 

amount

 

of

 

water

 

that

 

has

 

exceeded

 

the

 

system

 

capacity

 

over

 

the

 

last

 

4

 

regenerations.

  

When

 

remaining

 

goes

 

to

 

zero,

 

the

 

gallons

 

used

 

will

 

be

 

added

 

to

 

over

 

run

 

total.

The

 

current

 

flow

 

rate

 

and

 

the

 

peak

 

flow

 

rate

 

since

 

the

 

last

 

regeneration.

Advises

 

whether

 

a

 

delayed

 

regeneration

 

has

 

been

 

scheduled

 

manually

 

or

 

automatically.

The

 

current

 

setting

 

of

 

the

 

valve

 

mode.

Diagnostic Display 

10  

Summary of Contents for HTO-185HEUF
























Reviews: