background image

INTRODUCTION 

Thank you for purchasing the NorthFire-DVR36H/DVT36H Direct Vent Built-in Gas Fireplace 
Heater. 
 
The NorthFire-DV36H is one of the most advanced gas fireplace heaters on the market. It is 
designed using the latest technology and manufactured to the highest quality. 
 
Some of the many features are: 

 

∗ 

Small Size                      The NorthFire-DV36H is compact enough to fit into almost any size 

 room. 

∗ 

Heater Classification      The NorthFire-DV36H is classified as a heating appliance. Therefore, 

it can be operated continuously for zone heating. 

∗ 

High Efficiency              The NorthFire-DV36H has high efficiency, which means that it is 

less expensive to operate. 

∗ 

Adjustable Flame           The flame aesthetics and heat output can be adjusted to suit the 

 owner’s moods and heating needs. 

∗ 

Solid Construction         The NorthFire-DV36H is constructed mainly of satin coated and 

galvanized steel for long life and durability. 

 
Please read the manual carefully prior to installation and operation of the appliance. 
Proper installation, operation and maintenance of the appliance will provide you with 
many years of enjoyment. 

 

CAUTION 

 

Due to high temperatures, the appliance should be located out of traffic and away from 
furniture and draperies. 
 
Children and adults should be alerted to the hazards of high surface temperature and 
stay away to avoid burns or clothing ignition. 
 
Young children should be carefully supervised when they are in the same room as the 
appliance. 
 
Clothing or other flammable material should not be placed on or near the appliance. 
 
Any parts removed or opened for servicing of the appliance must be properly replaced 
prior to operating the appliance. 
 
The appliance must be inspected before use and at least annually by a qualified service 
person. More frequent cleaning maybe required due to excessive lint from carpeting, 
bedding material, etc. It is imperative that the control compartments, burners and 
circulating air passageways for the appliance be kept clean. 

f i r e - p a r t s . c o m

Summary of Contents for northfire dvr36h



























Reviews: