background image

Warner Electric • 800-825-9050

P-273-4-WE • 819-0528 

  

5

Installing the Motor Mount Bracket

A Motor Mount Bracket can be installed on the 
output end of a 1020 and 1040 UniModule to 
provide a foot mounting for the complete assembly 
of a UniModule and C-face motor. 

Optional Motor Mount Kit, 
Warner Electric part numbers:

UM-50/100............................5370-101-078
UM-180.................................5370-101-079

1. Mount the bracket to the face of the UniModule 

underneath the UniModule and motor as shown in 
Figure 5. A pilot diameter on the UniModule mates 
with a pilot diameter on the bracket.

Figure 5

2. Secure the motor bracket in place with four (4) 

short bolts and washers provided. Tighten to 18 
to 22 foot pounds.

Mounting to Other Power 

Transmission Components

Couplings, pulleys, sprockets or similar power 
transmission components can be mounted to the 
input and output shafts of a UniModule.

When mounting a pulley or 

sprocket, ensure that the key is fully engaged 
within the device hub or bushing.

Confirm that the belt or chain 

tightness meets the maximum side load 
capability of the UniModule shown in Table 2.

Overhung Load Data 

(Shaft Side Load)

Overhung load data is provided in this manual for the 
design engineer concerned with a specific problem 
in this area. The maximum allowable overhung load 
which can be applied to the shaft of an UniModule 
may be determined by the use of the accompanying 
chart.

Table 2

A

R

Distance Load is Applied from

  

 

Maximum

 UniModule 

Housing Face 

Load Rating

 

 

“A” Inches 

“R” Lbs.

 

UM-50 

1” (Center of Shaft) 

177

 

 

2” (End of Shaft) 

123

 

 

3” 

  95

    UM-100 

1” (Center of Shaft) 

192

 

 

2” (End of Shaft) 

134

  

3” 

104

  UM-180 

1” (Center of Shaft) 

192

 

 

2” (End of Shaft) 

134

  

3” 

104

Summary of Contents for UM-50











Reviews: