background image

Rev. 1.1

 

Assembly Instructions - Hand-Spray Valve SMS-15  

Page 9 of 18 

 

 

 

Walther Systemtechnik GmbH 

– D 76726 Germersheim 

Telefon: +49 (0)7274-7022-0 Telefax: +49 (0)7274-7022-91 
http://www.walther-2000.de 

– [email protected] 

 

5.2  Mounting and Installation 

The  valves  can  be  installed  in  any  position.  The  distance  to  the  application  area  depends  on  the  desired 
application  width.  You  can  use  round  and  flat-jet  caps.  An  intermitting  operation  of  the  device  will  cause 
natural oscillations; therefore a solid installation is most important. Try to avoid excessive natural oscillations 
(transmission from device to valve). 

5.3  Hose Mounting  

There are three functional hoses which will be connected as follows (see definition of interfaces):  

 

1. 

Atomizer air (blue) to ZL   

M5 

– connection "ZL" - Pos. 2.4 

2. 

Control air (black) to SL 

 

M5 

– connection "SL" - Pos. 2.4 

3. 

Material (transparent) to M  

1/8"-connection "M" - Pos. 2.3 

5.4  Connection Diagram (separate controls) 

 

5.5  Adjusting the Device  

The  stroke  adjustment  of  the  needle  will  be  used  for  setting  the  material  quantity.  A  left  turn  of  the  raster-
needle locking screw will increase the material quantity. A finely ascending precision thread results in a nee-
dle stroke which changes 0.5mm with one turn of the raster head. 

 

 

IMPORTANT 

The maximum turn of the raster-needle locking screw anti-clockwise should not exceed 
the  noticeable  raster  steps.  This  will  already  exceed  the  maximum  needle  stroke  ad-
justment.  
If you continue turning, the raster-needle locking screw will be dislocated! 

 

 

IMPORTANT 

Nozzle and nozzle needle can be damaged by wrong treatment. Only reduce the mate-
rial  flow  with  emerging  material  (right  turn  of  adjusting  screw).  Do  not  turn  adjusting 
screw further to the right after closing of the nozzle! 

 

Controls not included in 
scope of delivery 

Summary of Contents for SMS-15



















Reviews: