background image

Rev. 1.1

 

Assembly Instructions - MINI-Full-Jet Valve VMS-08 

Page 11 of 16 

 

 

 

Walther Systemtechnik GmbH 

– D 76726 Germersheim 

Telefon: +49 (0)7274-7022-0 Telefax: +49 (0)7274-7022-91 
http://www.walther-2000.de 

– [email protected] 

 

8  Maintenance and Repair 

8.1  General Information 

 

CAUTION 

Before  starting  any  maintenance  or  repair  work,  ensure  that  all  air-operated  tools  are 
depressurized and disconnected from the air supply. 
Before opening the spray valve it must be disconnected from the air and fluid supply. 
Otherwise, ejected components can cause injuries. 

 
The full jet valves of the 

VMS-08

 series are high precision tools. Always keep clean and observe minimum 

instructions to maintain a long and useful life of valve. We recommend lubricating moveable parts regularly, 
and  greasing  threads,  especially  the  nozzle  threads,  when  replacing  or  cleaning  the  nozzle.  It  is 
recommended to use clean and filtered application fluid only. The control air should also be clean and slightly 
oiled. Individual operating conditions and differing media require a minimum and regular routine care. 

8.2  Cleaning  

Wash equipment thoroughly after use to remove residues and dirt, especially if needle (pos.5), needle gasket 
(pos.4.2) or nozzle (pos.1) is to be exchanged. 

 

 

IMPORTANT 

Only use soft brushes for outside cleaning of the nozzle tips. Never use metal tools 
with sharp edges! 

 

 

IMPORTANT 

Do not start any repair work on the installed device. Remove the device from the ma-
chines first. (Disconnect from the air and fluid supply!) 

 

8.3  Routine Tasks 

No. 

Description  

Cleaning  

Lubricating   Inspecting  

Additional  

Frequency  

1. 

Connecting lines 

(tightness) 

 

 

 

Monthly  

2. 

Luer-Lock 

X

 

 

X

 

Replace when 

damaged  

Monthly  

 

8.4  Spare Parts 

 

IMPORTANT 
Only use original spare parts from the manufacturer! 
 

Wrong  or  defective  spare  parts  from  other  manufacturers  can  damage  the  device.  If 
other than original spare parts of the manufacturer will be used, all obligations from the 
manufacturer  or  his  sales  partners,  such  as  guarantees,  service  contracts  etc  will  be 

forfeited

 without further notice. 

 

 

Summary of Contents for VMS-08

















Reviews: