background image

Auxiliary Battery Kit w/Dual Cables          

80101569

 

Page 5 of 6 

 

 

 

For trailer applications with dual pole socket:  

Using 0 ga. cables, supplied with trailer kit, feed each 
end through battery-box wall and install a compression 
terminal on both red and black cables.  

Do not connect any cables to batteries at this time. 

Run cables from battery box to trailer nose, securing 
them every 24” with cable ties. 

 

 

 

 

 

 
For trailer applications with dual pole socket: 

Install dual pole socket in nose of trailer.  Drill 1-3/4” 
hole in trailer and mount with hardware provided. 

Route cables from auxiliary batteries to nose of trailer. 

Install cables to socket as shown. 

Apply a generous amount of Dielectric Grease over 
cable terminals. 

IMPORTANT: Be sure to orientate cables as shown, 

power (+) to the left, ground (-) to the 
right. 

 

 

 

 

 

Power (charge) cable from tractor batteries 
to trailer must also be protected with a 150 
amp circuit breaker at the tractor batteries. 

 

 

 

 

GR02770 

 

Note:  
While these instructions can be used for single pole 
sockets, Waltco recommends dual pole sockets be 
used for their superior grounding abilities. 

For trailer applications with single pole socket: 

Using 0 ga. cable, supplied with trailer kit, feed the end 
through battery-box wall and install a compression 
terminal on that end.  

Do not connect any cables to batteries at this time. 

Run cable from battery box to trailer nose, securing 
them every 24” with cable ties. 

 

 

Dual Pole Socket 

Attach Ground (-) 
Cable This Side 

Attach Power (+) 
Cable This Side 

Cables made from 
0 ga. cable 

40

Summary of Contents for GT-33













































Reviews: