background image

0

.  GAS MOTOR SAFETY

BEFORE STARTING ENGINE, READ

AND UNDERSTAND THE OPERATING 

AND MAINTENANCE INSTRUCTIONS

THAT CAME WITH YOUR ENGINE.

WARNING: DO NOT

1.  DO NOT run engine in an enclosed area.  

Exhaust gases contain carbon monoxide, an 

odourless and deadly poison.

2.  DO NOT place hands or feet near moving or 

rotating parts.

3.  DO NOT store, spill, or use gasoline near an 

open flame, or devices such as a stove, furnace, 

or water heater which use a pilot light or devices 

which can create a spark.

4.  DO NOT refuel indoors where area is not well 

ventilated.  Outdoor refuelling is preferred.

5.  DO NOT fill fuel tank while engine is running.  

Allow engine to cool for 5 minutes before refuel-

ling.  Store fuel in approved safety containers.

6.  DO NOT remove fuel tank cap while engine is 

running.

7.  DO NOT operate engine if gasoline is spilled.  

Move machine away from the spill and avoid 

creating any ignition until gasoline has evapo-

rated.

8.  DO NOT smoke while filling fuel tank.

9.  DO NOT choke carburetor to stop engine.  

Whenever possible, gradually reduce engine 

speed before stopping.

10. DO NOT run engine above rated speeds.  This 

may result in injury or engine failure.

11.  DO NOT tamper with governor springs, gover-

nor links or other parts which may increase the 

governed speed.

12. DO NOT tamper with the engine speed selected 

by the original equipment manufacturer.

13. DO NOT check for spark with spark plug or 

spark plug wire removed.

14  DO NOT crank engine with spark plug removed.  

If engine is flooded, place throttle in "FAST" 

position and crank until engine starts.

15. DO NOT strike flywheel with a hard object or 

metal tool as this may cause flywheel to shat

-

ter in operation.  Use proper tools to service 

engine.

16  DO NOT operate engine without a muffler.  

Inspect periodically and replace, if necessary.  

If engine is equipped with a muffler deflector, 

inspect periodically and replace, if necessary 

with correct deflector.

17. DO NOT operate engine with an accumulation 

of grass, leaves, dirt or other combustible mate-

rials in the muffler area.

18. DO NOT use this engine on any forest covered, 

brush covered, or grass covered unimproved 

land unless a spark arrester is installed on the 

muffler.  The arrester must be maintained in 

effective working order by the operator.  In the 

state of California the above is required by law 

(Section 4442 of the California Public Resourc-

es Code).  Other states may have similar laws.  

Federal laws apply on federal land.

19. DO NOT touch hot muffler, cylinder or fins be

-

cause contact may cause burns.

20. DO NOT run engine with air cleaner or air 

cleaner cover removed.

WARNING: DO

1.  ALWAYS DO remove the wire from the spark 

plug when servicing the engine or equipment 

TO PREVENT ACCIDENTAL STARTING.  Dis-

connect the negative wire from the battery ter-

minal if equipped wit a 12 volt starting system.

2.  DO keep cylinder fins and governor parts free of 

grass and other debris which can affect engine 

speed.

3.  DO examine muffler periodically to be sure it is 

functioning effectively.  A worn or leaking muffler 

should be repaired or replaced as necessary.

4.  DO use fresh gasoline.  Stale fuel can gum 

carburetor and cause leakage.

5.  DO check fuel lines and fittings frequently for 

cracks or leaks.  Replace if necessary. 

Summary of Contents for LX100














































Reviews: