background image

27-05-19 UNI-SAN Domestic Instructions Page 1 

 

 

 

 

 

UNI-SAN DOMESTIC 

 
 
 
 

Automatic waste water only collection tank and electrically operated pump 

system. 
 

 

INSTALLATION AND SERVICING INSTRUCTION MANUAL

 

 

PLEASE READ ALL INSTRUCTIONS PRIOR TO PROCEEDING WITH ANY WORK 

A permit may be required. Check with the plumbing and drainage and the electrical inspectors before installation.   
Local regulations may stipulate additional installation requirements.  
 
AFTER INSTALLATION, THE INSTALLER MUST HAND THIS MANUAL TO THE OWNER FOR THE PROPER 
OPERATION AND MAINTENANCE OF THE UNIT.  Failure to do so will result in the installer being liable under 
current legislation for future claims resulting from incorrect operation or servicing.  

 

Figure 1 :  Dimensions 

 

 

Figure 2 : 

Cut-away view through the cover showing the dry mounted    

 

 

 

 

pump and motor unit, mounted on a sealed gas and water-tight tank.

 

 
 
 
 

 
 
 
 

 
 
 
 
 
 
 
 

 

 
 
 
 
 
 
 
 
 
PAGE INDEX

 

Section 
1. General view and connections.................  2 
2. Product 

overview 

............................... 3 

3. Applications 

....................................... 

4. 

Features & benefits............................ 4 

5. 

Overall building design and  

                          Pump hydraulic capability...  4 
6. 

Warning : for your safety....................  5 

7. 

List of fittings supplied,  

           recommended extras and tools.........  6 

 

Section 
8. 

General installation aspects  

                    and electrical data.....................  6 
 9. 

Specific installation procedures..........  7 

 

Shower tray or bath plug height..........  8 

10. Care 

and 

servicing............................. 9 

11. 

Warranty and Limitations....................10 

Appendix A:  Rotating the delivery direction...11 
Appendix B : Fault finding chart......................11 
Appendix C : Remote installations..................14

 

 

Limitations :  We reserve the right to change these instructions and improve the product without prior notice.  

 
 AUCKLAND 

   PALMERSTON 

NORTH 

  CHRISTCHURCH 

  

 55 

MAURICE 

RD, 

PENROSE 

     35 

BUCHAN 

ST 

 

PO BOX 12 387 

 

 

 

 

 

 

SYDENHAM 

 

PH     09   622 9100 

 

 

PH/FAX 06  323 4445 

 

 

PH     03   365 6453 

 

FAX   09   622 9119 

 

 

 

 

 

 

FAX   03   366 6995 

A division of CONSOLIDATED ALLOYS (NZ) Limited. 

1.  GENERAL VIEW & CONNECTIONS

 

UNI-SAN 

 

Pump cover 

O-ring sealed lid 

Gas and 
watertight 
collection unit 

Dry mounted pump and motor 
unit 

Vent and inlets 
can be fitted 
wherever 
required on 
tank

Gas and watertight 
collection tank 

Summary of Contents for UNI-SAN
















Reviews: