background image

68 

Parameterizing 

WAGO-TO-PASS® 761 

 

 

761-214 Telecontrol Module Compact, 8 AI, ESP, DSP 

 

Manual 

 

Version 2.0.0  

  

7.6 

Configuring Error Detectors 

The 

TO-PASS

®

 telecontrol module can transmit error messages to a maximum of 

four recipients. The recipients are informed either directly one after another or (if 
configured) after expiration of the time delay for acknowledgment. The message 
is sent by the 

TO-PASS

®

 telecontrol module as an SMS; however, it can also be 

sent as an e-mail, fax or voice mail. In addition, the error messages can also be 
transmitted to a Web portal. 

 

 

 

Device-dependent Function 

Devices with GPRS functionality (device identifier "Web") are required to 
transmit error messages to a Web portal. 

 

 

 

 

Note the calculation packet size! 

Please note the information given on calculation packet size in the Section 
"Important Information - Rounding of Blocks for GPRS Links." 

 

  

7.6.1 

Alarm Messages for Digital Inputs 

If on or off states of digital inputs are to be sent as error messages, select the 
desired recipient for the respective input statuses using buttons 

[1]

 ... 

[4].

 Click 

the 

[Internet]

 button to also transmit the message to a Web portal.  

In addition, you can also specify the analog values that are to be transmitted along 
with the error message. 

  

7.6.2 

Limit Messages for Counter Inputs 

If violations of upper/lower counter limits are to be sent as error messages, 
activate the respective counter value and select the desired recipient using buttons 

[1]

 ... 

[4]

.  

Click the 

[Internet]

 button to also transmit the message to a Web portal.  

 
You can also specify the analog values that are to be transmitted along with the 
error message. 

  

7.6.3 

Limit Messages for Analog Inputs 

You can specify a maximum of 2 limit values for every analog input for which 
(upper/lower) limit value violations are to be sent as error messages.  
Enter the desired value and select whether the error message is to be sent for 
violation of the upper or lower limit value using the buttons [

increasing] 

or 

[

decreasing]

.  

Select the desired recipient for the respective limit value using the buttons 

[1] … 

Summary of Contents for 761-214







































































































Reviews: