manualshive.com logo in svg

WAGO 750-527, Manual

Share
Download
WAGO 750-527 Manual Download Page 50

50  List of Tables 

WAGO-I/O-SYSTEM 750 

 

 

750-527 4DO 30V AC/DC 2.0A SSR 

Manual 

 

Version 1.0.0  

 

 

List of Tables 

Table 1: Number Notation ................................................................................... 8

 

Table 2: Font Conventions .................................................................................. 8

 

Table 3: Legend for Figure “View” ......................................................................17

 

Table 4: Legend for Figure “Power Jumper Contacts” ........................................19

 

Table 5: Legend for Figure “CAGE CLAMP

®

 Connectors” ..................................21

 

Table 6: Legend for Figure “Display Elements”...................................................22

 

Table 7: Technical Data 

‒

 Device .......................................................................23

 

Table 8: Technical Data 

‒

 Digital Outputs ..........................................................23

 

Table 9: Technical Data 

−

 Field Supply ..............................................................24

 

Table 10: Technical Data – Local Bus Supply ....................................................24

 

Table 11: Technical Data – Isolation ..................................................................24

 

Table 12: Technical Data – Communication .......................................................24

 

Table 13: Technical Data – Field Wiring .............................................................25

 

Table 14: Technical Data – Power Jumper Contacts ..........................................25

 

Table 15: Technical Data – Data Contacts .........................................................25

 

Table 16: Environmental Conditions ...................................................................25

 

Table 17: Output Bits..........................................................................................28

 

Table 18: Legend for Figure “Power Supply for Voltage Ranges up to  

31.2 VDC”

 .................................................................................................34

 

Table 19: Legend for Figure “Power Supply for AC Voltage Ranges or  

DC Voltages above 31.2 VDC”

 ..................................................................35

 

Table 20: Description of the Marking Example per ATEX and IECEx .................40

 

Table 21: Description of the Marking Example of an Approved I/O Module  

Ex i per ATEX and IECEx..........................................................................42

 

Table 22: Description of Marking Example According to NEC 500 .....................43

 

Table 23: Description of Marking Example for Approved Ex i I/O Module 

According to NEC 505 ...............................................................................44

 

Table 24: Description of Marking Example for Approved Ex i I/O Modules 

According to NEC 506 ...............................................................................44

 

Table 25: Description of Marking Example for Approved Ex i I/O Modules 

According to CEC 18 attachment J ...........................................................45

 

 

  

 

Summary of Contents for 750-527





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands