manualshive.com logo in svg

WAGO 750-527, Manual

Share
Download
WAGO 750-527 Manual Download Page 15

WAGO-I/O-SYSTEM 750 

Device Description  15 

750-527 4DO 30V AC/DC 2.0A SSR

Manual 

Version 1.0.0 

3 

Device Description 

The I/O

 

module  750-527 (4DO 30V AC/DC 2.0A SSR) acts together with the 

MOFSET transistors to switch voltages up to 30 VAC or 48 VDC (for resistive 

loads).  

 

The semiconductor switches attached to the CAGE CLAMP

®

 connection 

substitute for relay contacts. Because of their wear resistance, application 

availability is increased.

 

The I/O module has 4 output channels, providing a direct connection to 2-wire 

actuators.

 

The actuators are connected to the following CAGE CLAMP

®

 connectors

: DO 1 

or DO 2, DO 3 or DO 4 and 0 V.

 

The assignment of the connections is described in the “Connectors” section. 

Although the semiconductor outputs are not continuously protected against short 

circuit, they are highly resistant against pulse currents, so an external switched 

fuse is promptly tripped in case of short circuit.  

In addition to a suitable fuse, the output transistor withstands brief overcurrents 

until switch-off without damage

. 

Connection examples are shown in section “Connect Devices” > … > 

“Connection Example(s)”. 

A green LED indicates the switched status of each channel. 

The meaning of the LEDs is described in the “Display Elements” section. 

Use supply modules for ground (earth)! 

The I/O module has no power jumper contacts for receiving and transmitting the 

earth potential. Use a supply module when an earth potential is needed for the 

subsequent I/O modules. 

The I/O module 750-527 (4DO 30V AC/DC 2.0A SSR) receives the power supply 

of up to 30 VAC (or 48 VDC for resistive loads) via the power jumper contacts 

designed as blade contacts from an upstream power supply and provides it to 

downstream I/O modules via the power jumper contacts designed as spring 

contacts. 

Summary of Contents for 750-527





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands