manualshive.com logo in svg

WAGO 750-527, Manual

Share
Download
WAGO 750-527 Manual Download Page 34

34  Connect Devices 

WAGO-I/O-SYSTEM 750 

 

 

750-527 4DO 30V AC/DC 2.0A SSR 

Manual 

 

Version 1.0.0  

 

 

6.2 

Power Supply Concept 

 

 

 

 

AC voltage and DC voltages above 31.2 VDC 

 

An additional supply module (e.g., 750-612) is needed for AC voltage or DC 

voltages above 31.2 VDC. In this scenario, mounting I/O modules with field

-side 

supply of only 31.

2 VAC or less in front of or behind the power supply is 

prohibited. Thus, when using AC voltages and DC voltages above 31.2 VDC, an 

individual supply segment! 

 

 

6.2.1 

Power Supply for Voltage Ranges up to 31.2 VDC

  

F

or voltage ranges up to 31.2 VDC (≤24 V + 30%), field power supply (load 

voltage) is possible at the head station (coupler power supply), the bus power 

supply (750-613) or through other power supplies (e.g., 750-602; or 750-601, 

750-610 with adequate sum current).  

The 750-527 I/O Module receives its field voltage via the power jumper contacts. 

 

Figure 11: Power Supply for Voltage Ranges up to 

31.2 VDC

 

Table 18: Legend for Figure “Power Supply for Voltage Ranges up to 

31.2 VDC”

 

Pos. 

Explanation 

1 

Head station 

2 

I/O Modules 

(24 VDC; e.g., 750

-430 or 750-530) 

 

3 

750-

527 I/O Module (voltage range up to 31.2 VDC)

 

 

4 

I/O Modules 

(24 VDC; e.g., 750

-430 or 750-530) 

 

5 

End Module (750-600) 

 

U

S

 

System power supply 24 VDC

 

 

U

F

 

Field power supply 24 VDC

 

 

 

 

Summary of Contents for 750-527





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands