background image

WAFER GSM-RELAY REMOTE CONTROL UNIT 

http://www.waferlife.com 

#QUERY White List

If you are not sure a number in the position of the device,you can use the SMS 
#PWD123456#QUERY=132324242 
The device would answer the SMS with: QUERY RESULT: 132324242 AT WHL121 
Or QUERY RESULT: 132324242 NOT EXIT 
 

#GOT Relay working output delay time. 

 

This command is useful in case you need to keep the Relay output working longer. The standard 
time is 0,3 seconds (300 ms). You can change it with the GOT command. 
• The syntax of the command is the following: 

#PWD123456#GOT500  

(

PC$PHONE)(Only for NO.1 Relay) 

Acknowledge

DELAY TIME SET TO 0500MS

 

With the above command the delay time has been set to 500 ms (0,5 seconds). 
• You can check what the current relay output delay time is with the command 

#PWD123456#GOT?  

(

PC$PHONE) (Only for NO.1 Relay) 

Acknowledge

DELAY TIME IS 0500 MS 

 

Also you can change the Timer Ratio from millisecond to Second or Minute 
#PWD123456#TIMER-DELAY-AT-MILLISECOND; 
#PWD123456#TIMER-DELAY-AT-SECOND; 
#PWD123456#TIMER-DELAY-AT-MINUTE; 

 
#MODE Relay Operation Mode SETUP   

(PC$PHONE) (Only for NO.1 Relay) 

#PWD123456#MODE0 

Acknowledge

:    RELAY SET TO MODE0 

#PWD123456#MODE1 

Acknowledge

:    RELAY SET TO MODE1 

If setup to MODE0,that is Momentary pulse mode, when you call the SIM card number , device will toggle the 

relay and delay a GOT timer ,then the relay will back the previous status. 

If setup to MODE1,that is Ratchet relay mode,when you call the SIM card number,device will switch to the 

other status ON or OFF ,and when you call again ,it will switch the status again. 

#PWD123456#MODE?        (Check the RELAY MODE Status) 

Acknowledge

:    RELAY IS MODE0    or RELAY IS MODE1 

 
#OUT Relay output control   

(1)ON the relay output contact 

#PWD123456#OUTX=ON  

(

PC$PHONE)

 

Where X is the number of the relay in the list (X is from 1 to 6)

 

Acknowledge

:

 

OUTX ON OK 

(2)OFF the relay output contact 

#PWD123456#OUTX=OFF  

(

PC$PHONE)

 

Where X is the number of the relay in the list (X is from 1 to 6)

 

Acknowledge

:

 

OUTX OFF OK 

(3)

ALL the relay control at the same time

 

Summary of Contents for GSM-RELAY6













Reviews: