background image

When the characteristics of an installation dictate that 
one or more of the extraction vents will not be used, 
these vents should be sealed using the special 
blanking caps provided. This will stop any leaks and 
ensure that air from the areas involved is properly 
extracted. 
 
 
 

Safety 
 

• Do not use this appliance for functions other than 

those described in this booklet 

• After removing the appliance from its packaging, 

ensure that it is complete and undamaged. If in 
doubt contact a professionally qualified electrician or 
VORTICE. Do not leave packaging within the reach 
of children or infirm persons

 

• Certain fundamental rules must be observed when 

using any electrical appliance, including: 
- never touch electrical appliances with wet or damp 

hands; 

- never touch appliances while barefoot; 
- never allow children or infirm persons to operate 

appliances unattended 

• Do not sit on or leave objects on the appliance. 
• Store the appliance out of the reach of children and 

infirm persons after deciding to disconnect it from 
the power supply and use it no more. 

• Do not use the appliance where flammable vapours 

are present (spirit, insecticides, petrol, etc.).

 

This appliance can be used by 

children no less than 8 years of 

age and by individuals with 

limited physical, sensory or 

mental capacities, or by 

inexperienced or untrained 

individuals, provided that they 

are supervised or have been 

instructed in safe use of the 

appliance and understand the 

associated risks. Children must 

not play with the appliance. 

Cleaning and maintenance 

procedures that can be 

undertaken by the user must not 

be entrusted to children, unless 

under supervision. 

The appliance must be installed 

by a professionally qualified 

electrician. 

The electrical system to which 

the product is connected must 

be in compliance with applicable 

regulations. 

Precautions must be taken to 

prevent gas coming from the gas 

flue pipe or from other fuel 

combustion units from entering 

into the room

• Do not make modifications of any kind to this 

appliance. 

• Do not expose this appliance to the weather (rain, 

sun, etc.). 

• Regularly inspect the appliance for visible defects.  

If any faults are found, do not operate the appliance; 
contact VORTICE immediately. 

• If the appliance does not function correctly or 

develops a fault, contact VORTICE immediately. 
Ensure that only genuine original VORTICE spares 
are used for any repairs. 

• Should the appliance be dropped or suffer a heavy 

blow, have it checked immediately by VORTICE. 

• The appliance must be installed by professionally 

qualified personnel. 

• The electrical system to which the appliance is 

connected must conform to applicable standards. 

• The appliance is double insulated and therefore 

does not need to be earthed. 

• The electrical power supply/socket to which the 

appliance is to be connected must be able to provide 
the maximum electrical power required by the 
appliance. If it cannot do so, arrange for a qualified 
electrician to make the necessary modifications. 

• A multi-pole switch must be used to install the 

appliance. The gap between the switch contacts 
must be no less than 3 mm. 

• Switch off the system’s main switch:  a) if the 

appliance does not function correctly; b) before 
cleaning the inside and outside of the appliance;  
c) if you decide not to use the appliance for any 
length of time.  

• Maintenance/Cleaning: On a yearly basis, have 

professionally qualified personnel check the level of 
grime that has accumulated. If necessary, use a dry 
cloth or a brush to clean the control components and 
fan blades.  Water should only be used to clean the 
adjustment vents. Do not immerse the appliance in 
water or other liquids. 

• Check that the air intake section, situated towards 

the outside, is clear.  

• The flow of air or fumes to be carried outside must 

be clean (that is free of grease, soot, chemical and 
corrosive agents, and explosive or flammable 
mixtures).  

• The appliance must not be used to activate water 

heaters, room heaters, etc. and it must not discharge 

 

ENGLISH

        

Warning: 

             

this symbol indicates that care must    

             be taken to avoid injury to the user

 

!

        

Caution: 

             

this symbol indicates that care must   

             be taken to avoid damaging the appliance

  

!

14

Summary of Contents for 12167





























Reviews: