Von Duprin PS914 Installation Instructions Manual Download

Page: 19 / 20

Installation

Instructions

900-BB Battery Backup

44487064 Rev. 10/10_a

44487064

INSTALL 900-BB ONTO MAIN CIRCUIT BOARD AND SECURE WITH SCREW

Plug Connector
Here

Secure with
Screw Here

(PS914 main board shown)

BATTERY SPECIFICATIONS

Battery Life

Model PS906 = 6A @ 24V
Model PS904 = 4A @ 24V

Model PS902 = 2A @ 24V
Model PS914 = 4A @ 24V

Battery Type

12VDC, 7Ah Gel Sealed Rechargeable Battery (2 included)
5 Year Service Life

Replacement Part Number

Schlage 991280

To avoid risk of electric shock,

turn off AC power to power

supply before installing or

wiring 900-BB board

DANGER:

Charge only Schlage 991280 batteries.

Other types may burst, causing personal injury

and damage. Observe the proper polarity

when connecting the batteries.

CAUTION:

}

Refer to installation instructions for compatible supply models - PS902, PS904, PS906, and PS914.

Suitable for Canadian Class IV standby power for access control

Summary of Contents for PS914





















Search results

Summary of Contents for PS914

Reviews:

Related manuals for PS914

Brands by name

Popular brands

Von Duprin PS914, Installation Instructions Manual

Search results

Summary of Contents for PS914

Reviews:

Related manuals for PS914

Brands by name

Popular brands