background image

911352_00(5)  Page 4 of 8

TYPICAL WIRING (continued)

Table 2. Wiring Requirements

Wiring

Type of Power

Transfer

(door to frame)

Maximum Wire

Length from Power

Supply to Power

Transfer

Minimum

Wire Gauge

Power Supply Input

Power Supply Output

(+24 and GND)

External Alarm, Fire Alarm,

Door Position Switch,

External Inhibit Device

EPT-10

EPT-10

Electric Hinge

Electric Hinge

EPT-10,

Electric Hinge

N/A

Per code

100 feet

200 feet

75 feet

150 feet

Per code

14 GA

12 GA

14 GA

12 GA

18-22 GA

Not critical

In this double door application, both doors open in the same direction and each is equipped with a Chexit. The two
Chexits are connected (ganged) by the gray (CM+) and violet (CM-) wires. (If not used, insulate these wires
separately.)
 When one Chexit is set into alarm, the other also goes into alarm, and both unlock after 15 seconds. A
fire alarm unlocks both doors at the same time. An external inhibit device also unlocks both doors at the same time.
After an external inhibit, the door that was used rearms 2 seconds after closing, and the unused door rearms after
the full rearm time. For proper operation, the rearm times of ganged Chexits must differ by at least 2 seconds.

Double Door Application

Wire Functions

Power 24 VDC

Common for NO output;
24 VDC, 1 A maximum

Normally open output;
closes during alarm

Communication line;
used to connect Chexits

Communication line;
used to connect Chexits

Fire alarm input;
0 VDC = fire,

24 VDC = no fire

Door position switch input;

0 VDC = door open,
24 VDC = door closed

External inhibit input;
0 VDC = Chexit inhibited,
24 VDC = Chexit active

Signal 24 VDC;
can be used to power

FA, DPS, and EI inputs

Power supply ground

Red

Blue

Brown

Violet

Gray

Yellow

Orange

Green

White

Black

+24

C

NO

CM-

CM+

FA

DPS

EI

S C

GND

The wiring requirements in Table 2

below must be followed.

IMPORTANT

!

+24

Power transfer

Power transfer

Cable to

Chexit

device

Cable to

Chexit

device

Red (+24)

Black (GND)

Blue (C)

Brown (NO)

Violet (CM-)

Gray (CM+)

Yellow (FA)

Orange (DPS)

Green (EI)

White (SC)

GND

_

+

Power

supply

output

Power supply

input

Red (+24)

Black (GND)

Blue (C)

Brown (NO)

Violet (CM-)

Gray (CM+)

Yellow (FA)

Orange (DPS)

Green (EI)

White (SC)

FIRE

Figure 3. Wiring Connections, Double Doors

Summary of Contents for Chexit CX33A/35A









Reviews: