background image

911352_00(5)  Page 8 of 8

Options are set by switches on the Chexit module. Before changing option settings, turn the Chexit off.
Changes in option settings take effect when the Chexit is turned on.

Seconds    Switch No. 1    Switch No. 2    Switch No. 3    Switch No. 4

0

2

4

6

8

10

12

14

16

18

20

22

24

26

28

 infinite

Rearm Time Switch Settings

off

on

off

on

off

on

off

on

off

on

off
on

off

on

off

on

off

off

on

on

off

off

on

on

off

off

on
on

off

off

on

on

off

off

off

off

on

on

on

on

off

off

off

off

on

on

on

on

off

off

off

off

off

off

off

off

on

on

on

on
on

on

on

on

Rearm Time Notes

1. Set the rearm time a few seconds longer than

the door will be open so the door closes before
the Chexit arms.

2. The Chexit is shipped from the factory with the

rearm time set to 10 seconds.

3. When the rearm time is infinite, the Chexit

arms when the door position switch detects
that the door is closed.

4. When the rearm time is infinite, you must open

and close the door after the Chexit is turned on.

5. If a door position switch is used, the Chexit

arms 2.5 seconds after the door closes.

6. If you are using a door position switch but you

want the full rearm time to expire before the
Chexit arms, call Von Duprin at 1-888-371-7331
and get instructions from Electrical Technical
Support.

7. For proper operation, the rearm time of each

ganged Chexit must differ by at least 2 seconds.

Location of Chexit

option switches

OPTIONS

Factory settings shown

8: Off
7: Off
6: Off
5: Off
4: Off
3: On
2: Off
1: On

Table 3. Chexit Options

Option

Rearm time

Nuisance delay

Nuisance alarm

Function

Switches Nos. 1 through 4 set amount of time you have to pass through door
after turning on key switch or using an external inhibit device (see table below)

If switch No. 5 is on, the pushpad must be pressed 2 seconds to set off alarm

If switch No. 6 is on, the Chexit horn sounds while pushpad is pressed during
nuisance delay; use in accordance with local code

Settings for Door No: ___

Self-test

Local fire alarm

If switch No. 7 is on, the Chexit performs a self-test when turned on; this
switch must be off for normal operation

If switch No. 8 is off, the Chexit internal horn sounds during a fire alarm

________ seconds

on                  off

on                  off

on                  off

on                  off

Summary of Contents for Chexit CX33A/35A









Reviews: