Volvo TAD1240GE Operator'S Manual Download Page 52

Page: 52 / 68

Diagnostic function

Code 2.8

Cause: Throttle potentiometer connected to CIU.

Response: The engine goes to idle. If the pedal is first re-
leased and then pushed down again the engine can be
operated on an emergency basis with the help of the idle
switch. (TAD1240-42GE)

Corrective action:

•

Check that the potentiometer is connected correctly.

•

Check that the wiring to the potentiometer is not
damaged.

•

Check the potentiometer.

Code 3.1

Cause: Oil pressure sensor.

Response: None.

Corrective action:

•

Check that the wiring to the sensor is not damaged.

•

Check that the sensor is connected correctly.

Code 3.2

Cause: Intake air temperature sensor.

Response: None.

Corrective action:

•

Check that the sensor connector is engaged correctly.

•

Check the wiring to the sensor.

•

Check that the sensor is mounted correctly.

•

Check that the sensor is functional.

Code 3.3

Cause: Coolant temperature sensor.

Response: Pre-heating is activated even if the engine is
warm.

Corrective action:

•

Check that the sensor connector is engaged correctly.

•

Check the wiring to the sensor.

•

Check that the sensor is mounted correctly.

•

Check that the sensor is functional.

Code 3.4

Cause: Charge air sensor.

Response: The engine smokes more than it usually does
when accelerating/under loading.

Corrective action:

•

Check that the wiring to the sensor is not damaged.

•

Check that the sensor is functional.

•

Check that the sensor is mounted correctly.

•

Check that the sensor is functional.

Code 3.7

Cause: Oil temperature sensor.

Response: None.

Corrective action:

•

Check that the wiring to the sensor is not damaged.

•

Check that the sensor is connected correctly.

Code 4.1

Cause Oil pressure warning lamp.

Response: Warning lamp does not function.
The diagnosis is activated if a circuit interruption is
detected during start-up.

Corrective action:

•

Check the w

arning lamp

•

Check the wiring and connection to the w

arning

lamp

Code 4.2

Cause: Warning lamp high coolant temperature.

Response: None.

Corrective action:

•

Check that the w

arning lamp

is correctly mounted.

•

Check the w

arning lamp

for run-indication.

•

Check the wiring and connection to the w

arning

lamp

Summary of Contents for TAD1240GE





































































Search results

Summary of Contents for TAD1240GE

Reviews:

Related manuals for TAD1240GE

Brands by name

Popular brands

Volvo TAD1240GE, Operator'S Manual

Search results

Summary of Contents for TAD1240GE

Reviews:

Related manuals for TAD1240GE

Brands by name

Popular brands