Volvo TAD1240GE Operator'S Manual Download Page 38 | Manualshive

Page: 38 / 68

background image

Maintenance

36

Fuel filter, change

NOTE! Do not fill the new fuel filter with fuel prior to
mounting, there is a risk that impurities can be intro-
duced into the system causing operational interrup-
tions or damage.

WARNING! Fuel filter replacement should be
carried out on a cold engine to avoid the risk of
fire caused by fuel spilling onto hot surfaces.

1. Clean the area around the fuel filter.

2. Drain the fuel filter, see “Fuel system, draining,

condensation water”.

3. Remove the filter using an appropriate filter

wrench.

4. Clean the filter’s sealing surface on the filter

housing.

5. Spread a thin layer of oil on the sealing ring and

mount the new fuel filter. Tighten the fuel filter ac-
cording to the instructions on the filter.

6. Purge the fuel system in proximity to the fuel fil-

ter, see ”Fuel system, purging”.

7. Operate the engine at a higher idle speed for ap-

proximately 10 minutes to remove any remaining
air from the system. Conduct leakage and
functional checks.

«
...
36
37
38
39
40
...
»

Summary of Contents for TAD1240GE





































































Reviews:

No comments

Related manuals for TAD1240GE

Brand: Navistar Pages: 24

Brand: Saito Pages: 2

Brand: Saito Pages: 2

Brand: Saito Pages: 7

Brand: Stobag Pages: 12

Brand: Atlas Imperial Diesel Engine Pages: 59

LZB 77 A0017-15

Brand: Atlas Copco Pages: 120

Brand: Volvo Penta Pages: 8

Brand: Volvo Penta Pages: 20

Brand: Toro Pages: 37

DYNAMIC LINE III

Brand: KEB Pages: 60

Brand: Canaline Pages: 43

Brand: Robin America Pages: 36

Brand: DLE Pages: 4

Brand: Toyota Pages: 338

Brand: Iveco Pages: 74

Brand: Briggs & Stratton Pages: 179

Brand: MVVS Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands