Volvo TAD1240GE Operator'S Manual Download Page 36 | Manualshive

Page: 36 / 68

background image

Maintenance

34

Coolant filter, change

1. Turn the valve (1) 90° to stop the flow through the

coolant filter.

2. Remove the coolant filter using an appropriate fil-

ter wrench. Make sure that no residue from the old
gasket remains on the housing.

3. Spread a thin layer of engine oil on the new

coolant filter’s gasket. Tighten the coolant filter by
hand until the rubber seal contacts the sealing
surface on the filter bracket. Tighten the coolant
filter 1/2 turn.

4. Turn the valve (1) 90° to start the flow through the

coolant filter again.

5. Start the engine and check for leaks.

6. Shut-off the engine and check the coolant level,

see ”Coolant level, check”.

«
...
34
35
36
37
38
...
»

Summary of Contents for TAD1240GE





































































Reviews:

No comments

Related manuals for TAD1240GE

Raptor JET SERIES

Brand: Indmar Pages: 82

Plug & Play Plus

Brand: CHERUBINI Pages: 16

Vanguard 290000

Brand: Briggs & Stratton Pages: 68

Brand: Oriental motor Pages: 8

Brand: MTU Pages: 239

Brand: Daedong Pages: 66

Brand: Man Pages: 18

Brand: Mercury Pages: 878

3564K024BC series

Brand: Faulhaber Pages: 60

Brand: Bosch Pages: 106

rexroth MSK 030

Brand: Bosch Pages: 72

Rexroth MKE Series

Brand: Bosch Pages: 134

Brand: Bosch Pages: 82

Brand: Bosch Pages: 124

Rexroth MKE E Series

Brand: Bosch Pages: 138

HYDRO-FORCE 65043

Brand: Bestway Pages: 8

Brand: Volvo Penta Pages: 44

Brand: Volvo Penta Pages: 90

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands