Volvo TAD1240GE Operator'S Manual Download Page 14 | Manualshive

Page: 14 / 68

background image

12

Instrument

1. Engine oil pressure.

2. Diagnosis lamps. The error codes are read from

the diagnosis lamp.

3. Coolant temperature.

4. Indicator lamps Pre-heating and after-heating.

5. Tachometer (rpm).

6. Throttle.

7. Start button.

8. ON button. Used to start the system. Sends

current to the system only when it is pushed. It
must therefore be held down until the main relay
is activated. This takes about one second.

9. Pre-heat button. Used to pre-heat the engine prior

to start. Pre-heating is automatically adjusted by
the system. The system also has after-heating.

10. Diagnosis button. Used to read out error codes.

See ”Reading out error codes”.

11. Stop/Off button.

12. Warning lights (x6) from the left: oil pressure, oil

temperature, battery charging, coolant tempera-
ture, coolant level, fuel alarm (includes both ”water
in fuel” as well as ”fuel pressure”).

Instrumentbox

«
...
12
13
14
15
16
...
»

Summary of Contents for TAD1240GE





































































Reviews:

No comments

Related manuals for TAD1240GE

Brand: BONFIGLIOLI Pages: 20

Brand: ALL POWER AMERICA Pages: 28

Brand: Master Pages: 2

NIIGATA MG(L)26HLX

Brand: IHI Pages: 204

Brand: ZF Pages: 80

AG2210-LP Series

Brand: Beckhoff Pages: 35

ZA top SM225.40B

Brand: ZIEHL-ABEGG Pages: 76

Brand: Motion Pages: 92

PS01-37x120F-HP-SSC-R/ FC

Brand: LinMot Pages: 40

2232***BX4 series

Brand: Faulhaber Pages: 60

Brand: ZIEHL-ABEGG Pages: 23

Brand: Nakayama Pages: 11

Brand: YewdaleDefiant Pages: 8

Brand: Yanmar Pages: 406

Brand: GAPOSA Pages: 8

Brand: Baldor Pages: 20

Brand: Yanmar Pages: 130

Brand: Parker Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands