Volvo Penta MD 11C/110S Instruction Book Download Page 27 | Manualshive

Page: 27 / 44

background image

- 25 -

LAYING-UP LAUNCHING

Install the battery, which should be fully charged. Grease the
cable shoes. Connect the battery cables.

IMPORTANT.

Do

(not)

reverse the polarity. Tighten the cable shoes well.

Remove the injectors. Take measure to avoid oil splash and run
the engine several turns so that the oil on the piston crowns is
blow out.
Refit the injectors. See "Tightening torques", "Technical Data".

Change the fuel filter cartridge. Pump forward the fuel and vent the
system. See "Venting the fuel system" (page 21).

Launch the boat. Start the engine. See the instructions on page 5.
Run the engine warm with the reverse gear engaged. Check to
make sure there is no leakage of fuel, air, water or exhaust gases.
Check that all the controls, etc., are functioning properly.

When necessary, contact an authorized Volvo Penta Service
Shop, and let them service the engine and reverse gear according
to the instructions in the servicing scheme.

«
...
25
26
27
28
29
...
»

Summary of Contents for MD 11C/110S













































Reviews:

No comments

Related manuals for MD 11C/110S

Brand: FAZUA Pages: 76

Brand: MTD Pages: 40

Brand: Jula Pages: 17

Air Cooled TR-10D

Brand: Wisconsin Pages: 46

Brand: Briggs & Stratton Pages: 6

WEST EUROTECH 36 T2

Brand: Weston UK Pages: 3

5.7L Corvette 2004

Brand: Chevrolet Pages: 1000

Brand: A'OK Pages: 7

Brand: Black Bruin Pages: 70

Brand: Wilesco Pages: 2

Brand: Wilesco Pages: 4

Brand: Wilesco Pages: 4

Brand: Wilesco Pages: 4

Brand: Wilesco Pages: 4

Brand: YS Pages: 2

Brand: HAMPTON BAY Pages: 17

Brand: Wren Turbines Pages: 13

Brand: Wren Turbines Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands