Volvo Penta 3.0GLP-C Owner'S Manual Download Page 30 | Manualshive

Page: 30 / 136

background image

Instrumentation

26

VPA 7743722 English 10-2004

22781

22782

22783

Trim Instruments

The trim instrument indicates the current trim position.
Your boat may be equipped with an analog or a digital
trim instrument. The SX drive has an analog trim in-
strument only. The DP-S drive may have either an an-
alog or a digital trim instrument.

Analog Trim Instrument

The analog trim instrument has three main ranges:

•

Trim Range

–Use trim range for maximum com-

fort, under normal operation, from start to maxi-
mum speed.

•

Beach Range

–Use beach range for operating at

reduced speed in shallow water, where water
depth is uncertain. Also use this range when you
launch and take your boat out of water onto a
trailer ramp.

•

Lift Range

–Use lift range for lifting the drive to

its maximum angle; however, this range cannot
be used during boat operation. Use this range

ONLY

when you are transporting your boat.

CAUTION! Operating in beach range or lift
range will cause significant loss of maneu-
verability.

WARNING! The maximum safe engine speed
in the Beach Range is 1000 RPMs. Operating
in beach range above idle speed, or for pro-
longed periods of time, may cause serious
drive damage. Always check that the cooling
water intake is below the surface of the water
when running in Beach Range.

7743722 - Downloaded from www.volvopenta.com 13/05/2008 20:17:06

«
...
28
29
30
31
32
...
»

Summary of Contents for 3.0GLP-C









































































































































Reviews:

No comments

Related manuals for 3.0GLP-C

Brand: Mack Pages: 303

Brand: Ibiza Pages: 3

Brand: Aerotech Pages: 59

Brand: Wacker Neuson Pages: 44

Brand: CG Pages: 45

Brand: 3W Pages: 20

24 v High Performance Synchronous Motor

Brand: Rega Pages: 1

Brand: Nouvag Pages: 8

Brand: Chamberlain Pages: 20

Brand: Chamberlain Pages: 28

Brand: VM Pages: 108

Brand: YS Pages: 2

Brand: Honda Pages: 46

Brand: Honda Pages: 2

Brand: Mitsubishi Pages: 76

Brand: HSD Pages: 72

Brand: Hirth Pages: 34

Brand: Vetus Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands