background image

VOLT

®

 Tranquility Brass LED Hanging Light 

VAL-9501-4036-BBZ

INSTALLATION INSTRUCTIONS

w w w . v o l t l i g h t i n g . c o m

Important: Please Read Before Installation

!

This luminaire is intended for installation in accordance with local codes 

and the National Electric Code (NEC). Failure to adhere to these codes and 

instructions may result in serious injury, property damage and void the 

warranty.

These instructions do not intend to cover all variations in installation, 

operation maintenance or mounting situations. 

1.  Make sure that the power is turned OFF before installing or servicing this 

luminaire. 

2.  WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or 

more from pool, spa or fountain.

3.  This luminaire is intended to be used only with a power supply 

(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.

4.  Wiring connections must be made with wire connectors that are suitable 

for outdoor use.

5.  The unit low voltage cable should: 

 

a) Be protected by routing in close proximity to the luminaire or  

 

 

fitting, or next to a building structure such as a house or deck;

 

b) Not be buried except for a maximum 6 inches (15.2 cm) in order to    

 

connect to the main low voltage cable; and 

 

c) Have the length cut off so that it is connected to a connector within   

 

6 inches (15.2 cm) from the building structure, a luminaire, or fitting.

6.  If additional lengths of low voltage cable are required, please contact 

www.voltlighting.com or call 1-813-978-3700.

Important Safety Instructions

!

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS

Lighted lamp is HOT!

WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.

1.  Turn off/unplug and allow to cool before replacing lamp.
2.  Lamp gets HOT quickly! Contact only switch/plug when turning on.
3.  Do not touch the hot lens, guard or enclosure.
4.  Keep lamp away from materials that may burn. 
5.  Do not touch lamp at any time. Use a soft cloth. Oil from skin may damage lamp.
6.  Do not operate the luminaire fitting with a missing or damaged shield.

SAVE THESE INSTRUCTIONS

Summary of Contents for VAL-9501-4036-BBZ








Reviews: