manualshive.com logo in svg

Vollrath STOELTING Flavor Burst STL-80BLD-DLX, Operator'S Manual

Share
Download
Vollrath STOELTING Flavor Burst STL-80BLD-DLX Operator'S Manual Download Page 54

51 

 

3.  Use the ampule provided to prime the 

cleaned area before mounting the Touch 
Panel mounting bracket.   

 

 

 

NOTE

:  LIQUID INSIDE THE AMPULE 

ENHANCES ADHESION. 

 

4.  Set the mounting plate on the freezer where 

it will be attached.   Measure and mark with 
a pencil around the base plate.     

 

 

 
5.  Remove the protective covering from the 

adhesive strip on the bottom of the base 
plate. 

The front of the plate is the side 

with the posts that are closest together

.  

Apply the base plate to the freezer within 
the pencil marks.  Press firmly and allow the 
adhesive to cure 

for at least 1 hour

.   

 

 

 

NOTE:

  IF THE ADHESIVE DOES NOT HAVE 

TIME TO CURE PROPERLY, THE CONSTANT 
WEIGHT OF THE TOUCH PANEL CAN PULL 
THE ADHESIVE AWAY FROM THE FREEZER 
SURFACE.  THIS COULD EVENTUALLY 
RESULT IN THE TOUCH PANEL ASSEMBLY 
FALLING OFF THE FREEZER.  
 
 

6.  Install the Touch Panel mounting plate to 

the back of the Touch Panel using the 
screws provided. Use the small lock 
washers in between the plate and screws. 

 

 

 

7.  Connect the ethernet cable to the “DRIVER 

BOARD 1” ethernet port behind the Touch 
Panel screen.  

 

 

 

NOTE:

  WHILE “DRIVER BOARD 2” PORT IS 

ALSO A VALID PORT, IT IS TEMPORARILY 
PLUGGED TO AVOID CONFUSION.  THE 
COLOR TOUCH PANEL PROGRAM 
DEFAULTS TO DRIVER BOARD 1.   

 

8.  Connect the straight end of the switch 

extension to the “PORT 1” switch port 
behind the Touch Panel screen.  

 

 

 

NOTE:

  WHILE “PORT 2” SWITCH PORT IS 

ALSO A VALID PORT, IT IS TEMPORARILY 
PLUGGED TO AVOID CONFUSION.  YOU 
WILL ACTIVATE THE PORT YOU USE WHEN 
YOU GO THROUGH THE EQUIPMENT 
SETUP WIZARD PROGRAM ON YOUR 
COLOR TOUCH PANEL LATER.   

 
 

Summary of Contents for STOELTING Flavor Burst STL-80BLD-DLX

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands