manualshive.com logo in svg

Vollrath STOELTING Flavor Burst STL-80BLD-DLX, Operator'S Manual

Share
Download
Vollrath STOELTING Flavor Burst STL-80BLD-DLX Operator'S Manual Download Page 51

48 

 

9.  Scroll down to the Maintenance Functions 

section and touch the key named “Flushing 
Functions”.   

 

 

 
 
10. Press the flavor line to be flushed and follow 

the instructions outlined on the Touch Panel 
to flush the syrup line until it is empty.   

 

 

 
11. When the line is empty, press CANCEL and 

disconnect the Pump Flush Adapter.  
Connect the Pump Flush Adapter to the 
next bag connector.    

 

 

 

NOTE:  

THE FLUSH FUNCTION WILL 

CONTINUE FOR 15 MINUTES.  YOU MAY 
STOP IT AT ANY TIME BY PRESSING 
“CANCEL”.  
 

12. Repeat Steps 10 and 11 for the second line, 

then the third, and so on until all the lines 
have been cleared of sanitizer solution.      
 
 

13. When all lines have been emptied, return 

the Pump Flush Adapter to the position 
under the trays. 
 
 

14. Ensure the Blending Assembly and the 

other parts are stored in a sanitary place for 
the off-season.  When opening next season, 
be sure to perform the Clean-In-Place 
procedure again to sanitize all pumps 
before recharging the system with syrups. 

 

 

 
 
15. When opening next season, be sure to 

perform the Clean-In-Place procedure again 
to sanitize all pumps before recharging the 
system with syrups.

 

Summary of Contents for STOELTING Flavor Burst STL-80BLD-DLX

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands