manualshive.com logo in svg

Vollrath STOELTING Flavor Burst STL-80BLD-DLX, Operator'S Manual

Share
Download
Vollrath STOELTING Flavor Burst STL-80BLD-DLX Operator'S Manual Download Page 44

41 

 

Refilling the Sanitizer Tank 

 
For day-to-day operations, use Flo-San®  
sanitizer mixed according to the manufacturer’s 
instructions in the sanitizer tank.  The tank 
system delivers solution to specific areas of the 
Flavor Burst

®

 system such as the Blending 

Head and syrup lines during certain 
functions.  Therefore, check the tank levels on a 
daily basis.  For proper sanitation, use only 
FRESH sanitizer solution in the tank that is no 
more than 28 days old.  Replace older solution 
with fresh sanitizer solution.   
 
1.  Disconnect the sanitizer tank from the 

sanitizer line.   

 

 

 

2.  Remove the sanitizer tank from cabinet.   

 

 

 

3.  Remove the sanitizer tank’s cap and discard 

any remaining Flo-San sanitizer solution. 
Rinse out the tank with water.     

 

 

 

4.  Mix one packet (0.50 oz) of Flo-San® with 

two gallons of warm water (108°F / 42°C) 
until dissolved.  Pour the sanitizer solution 
into the tank. 

 

 

 

 
5.  Reinstall the cap and tighten sufficiently.  

 

 

 

6.  Return the sanitizer tank to the cabinet.   

 

 

 

7.  Connect the tank to the cabinet using the 

sanitizer line.     

 

 

 
 

 
 

Summary of Contents for STOELTING Flavor Burst STL-80BLD-DLX

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands