Volkswagen 1999 Golf Diagnostic Manual Download Page 152

Page: 152 / 225

Volkswagen Jetta, Golf, GTI 1999, 2000
Electrical Equipment On Board Diagnostic (OBD)

Instrument panel On Board Diagnostic (OBD) (from MY 2000) (Page 01-151)

The last position of the kilometer reading must be rounded off to the nearest 10 kms. A kilometer
reading of 89627 produces an adaptation value of:

- Enter adaptation value using keyboard.

Indicated on display:

- Confirm entry with key Q.

Indicated on display:

The kilometer reading entered now appears in the display of the instrument panel. If the displayed
kilometer reading is not OK, e.g. false entry:

- Press C key and enter correct adaptation value again.

If the displayed kilometer reading in instrument panel is OK:

Summary of Contents for 1999 Golf


































































































































































































































Search results

Summary of Contents for 1999 Golf

Reviews:

Related manuals for 1999 Golf

Brands by name

Popular brands

Volkswagen 1999 Golf, Diagnostic Manual

Search results

Summary of Contents for 1999 Golf

Reviews:

Related manuals for 1999 Golf

Brands by name

Popular brands