Volkswagen 1999 Golf Diagnostic Manual Download Page 207

Page: 207 / 225

Volkswagen Jetta, Golf, GTI 1999, 2000
Electrical Equipment On Board Diagnostic (OBD)

Anti - theft immobilizer On Board Diagnostic (OBD) (Page 01-206)

Read Measuring Value Block

Indicated on display:

- Press buttons -0- and -8- to select "Read Measuring Value Block" function 08.

Indicated on display

- Confirm entry with -Q- button.

Indicated on display

- Press buttons -0-, -2 and -2-.

- Confirm entry with -Q- button.

Notes:

When the printer is switched on the actual display is printed out.

- Indicated on display, for example

Evaluating Measuring Value Block

Summary of Contents for 1999 Golf


































































































































































































































Search results

Summary of Contents for 1999 Golf

Reviews:

Related manuals for 1999 Golf

Brands by name

Popular brands

Volkswagen 1999 Golf, Diagnostic Manual

Search results

Summary of Contents for 1999 Golf

Reviews:

Related manuals for 1999 Golf

Brands by name

Popular brands