Voith 22000000700 Instruction Manual Download Page 20

 

Instruction Manual

Voith Turbo

 

Way Valve WSR-D16214

 

 

 

 

2005 / 03  aie 

Voith Turbo GmbH & Co. KG 

Page: 20 / 24

9183626018945 en 

D – 74564 Crailsheim 

Version: 2.0

 
 

7.3 Troubleshooting 

 

  Troubleshooting must only be performed in a non-hazardous atmosphere.  

 

 

  Prior to starting the work, make sure that the way valve was installed electrically and 

hydraulically according to the information provided in Chapter 5 and properly 
commissioned according to the information provided in Chapter 6. 

 
 

Malfunction

 

Possible cause(s) 

Remedy 

The piston rod 
shows temporary 
stroke variations. 

Air pockets and/or lack of 
damping 

De-aerate the way valve as per Chapter 6.1. 

 

Precondition: 
Disconnect external setpoint and connect
setpoint source directly to the way valve. 

Electrical fault on the 
connecting cable and/or 
vibration of the master 
controller 

Establish precondition and enter a constant
setpoint. If a stroke variation does no longer
occur, check the connecting line and/or the
master controller for malfunctions and/or
defects. 

Proportional gain set too high Establish precondition and realize setpoint step-

changes. If this causes periodic stroke
variations, readjust the gain. See Chapter 6.2.3.

The piston rod 
shows periodical 
stroke variations 

There is mechanical friction 
in the slide valve. 

Establish precondition. Enter setpoint w 0 8 mm
for t = 30 sec. Then increase the setpoint in one
step to 8.5 mA and keep it constant for 30 sec. If
the stroke varies in one of the two phases,
ingress of dirt into the slide valve may be the
cause. Open slide valve and clean interior parts.
In case of damage to the control edges and
surfaces, completely replace the way valve. 

Piston rod shows 
sporadic stroke 
variations 

Connecting fault and/or 
defective electric lines 

Connect setpoint source directly to the way 
valve. If this remedies the malfunction, check the 
electric line. 

 

Defect in the Voith control 
magnet 

Connect setpoint source directly to the way 
valve. If malfunctioning still continues, replace 
the control magnet. 

Summary of Contents for 22000000700


























Reviews: