manualshive.com logo in svg

Vogtlin SmartTrak 100 Series, Manual

Share
Download
Vogtlin SmartTrak 100 Series Manual Download Page 42

42 

 

 

 
 
 
 

NOTE: The valve will move to the desired position immediately when you press the enter 
key. 

 
 

IMPORTANT SAFETY NOTES ABOUT PURGING 

WARNING: When toxic or corrosive gases are used, purge unit 
thoroughly with inert dry gas before disconnecting from the gas 
line to prevent personnel from being injured when coming in 
contact with the instrument. Chapter 3 discusses how to purge 
your instrument. Always neutralize any toxic gas trapped inside 
the instrument before removing it from the gas line. 

 

 

WARNING: The flow rate in Purge is much greater than the 
calibrated full scale value and as a result can be dangerous. 

 

 

Change Setpoint Source Screen (mass flow controllers only) 

 

If you are already in the Lower Level Screens, push the right or left arrow until you reach 
the Change Setpoint Source screen. To get to this screen at any time: Press Escape—Press 
Enter—enter password and Press Enter. Then, press the Right or Left arrow until you 
reach this screen. The Change Setpoint Source screen allows you to re-configure the 
location and type of the setpoint for the SmartTrak controller. If you intend to supply the 
setpoint command signal from the Pilot Module or a computer using the RS-232 link, the 
display must show: 

 

Change Setpoint 

Source 

Pilot/RS232 

If, instead of using the Pilot Module or the RS-232 link, you prefer to supply an analog 
setpoint signal to the SmartTrak, press the enter button. “Pilot/RS232” will begin to blink. 
Use the up and down arrows to make your selection from the following choices: 

 

0-5 VDC 

0-10 VDC 

1-5 VDC 

0/4-20 mA 

Pilot/RS232 

Summary of Contents for SmartTrak 100 Series



















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands