manualshive.com logo in svg

Vogtlin red-y smart Series, Instruction Manual

Share
Download
Vogtlin red-y smart Series Instruction Manual Download Page 23

 

 

Title: Instruction manual PROFINET interface 

Date: Sept. 2020 

Ver: 04AD_Red-y_V2.1 

By: WES/HAE 

Page 23

 / 

30

 

 

 

 

 

 

 

Description: PID Select 

Data type: UINT16 

The controller consists of altogether 5 complete control parameter sets (see the corresponding 

documentation). Three of these sets were defined by the manufacturer and cannot be changed by the 

user (so-called manufacturer control parameter sets). Two sets can be changed at wish by the user (so-

called user control parameter sets). 

 

One set is used for the current control. This setting can be saved in EEPROM and is available again with 

the next activation. This set can be read, changed and re-written via ModBus access. Afterwards, the 

controller immediately works with the modified set. 

 

Function of the pre-defined control parameter sets: 

Due to the flow end values, the correspondingly applied control valve and the pressure ratios, these sets 

receive different values for the parameters P, I, D, F and N. We will discuss the function of the individual 

parameters later on in this manual. The aim is to provide the controller with the following different 

properties with the three sets: 

 

Value 

Type 

0 

User control parameter set 1 (default) 

1 

User control parameter set 2 

2 

Manufacturer control parameter fast:  

Fast response time with the corresponding overshooting (fast response) 

3 

Manufacturer control parameter set medium: 

Medium response time with a low overshooting tendency. 

4 

Manufacturer control parameter set slow: 

Slow response time without overshooting (slow response) 

 

Description: Enable SP (Set Point) Storage 

Data type: UINT16 

To activate the Set Point Storage, the controller mode (Output PDO:  Device Setup) 

has to be

 in mode 1 

(Digital). 

 

Specifies whether the set value is automatically stored in the EEPROM. The service life of an EEPROM 

depends on the number of write cycles. The guaranteed number of write cycles is 1 million. If the set 

value is set every 10 minutes, the resulting service life is 19 years. 

If the set value is set at significantly shorter intervals, automatic storage should be disabled. 

 

0 = Manual save mode 

1 = Automatic save mode 

Description:  Pressure PID Select 

Data type: UINT16 

PID set selection for the pressure controller 

Summary of Contents for red-y smart Series































Reviews:

No comments

Brands by name

Popular brands

Load more brands