11
Getting Connected Cont...
CONNECTING EFFECTS USING THE EFFECT LOOP
By using the built-in EFFECT LOOP you can add external effects to vocals and/or music without compromis-
ing the quality of the original signal. We have equipped the GIG-MASTER with 3 “Loop Bars” to fill all the
EFFECT LOOP inputs and outputs. The Loop Bar for the MIC IN/OUT EFFECT LOOP enables the internal MIC
EFFECTS, and without this bar or other effect device in place, there will be no mic signal output. To use the
effects loop to connect external effects, remove the Loop Bar and replace it by using RCA cables. Connect
one RCA cable from the GIG-MASTER’s MUSIC/MIC OUT jack to the effects unit input. Then connect
another RCA cable from the effects unit output into the GIG-MASTER’s MUSIC/MIC INPUT jack. Use the MIC
IN/OUT when adding effects to the vocals and use the MUSIC IN/OUTs for LEFT and RIGHT when adding ef-
fects to the music.
EFFECT LOOP
L-MUSIC-R
MIC
OUT
IN
CLG-600
DUAL CHANNEL COMPRESSOR
LIMITER WITH GATE
THRESHOLD
dB
+10
1
2
4
6
9
12
15
18
21
24
27
30
+6
+3
0
-3
-6
-10
-20
-30
-30
-20
0
-40
+20
-10
RATIO
MANUAL
AUTO
N.1
ATTACK
PROCESS
mSec
RELEASE
Sec
OUTPUT
dB
0.5
OUT
IN
COMPRESSOR/LIMITER
ENHANCER
MONO
STEREO
OFF
THRESHOLD
INAUDIBLE
+
-
dB
+10
0
-50
-35
-10
-20
EXPANDER/GATE
8
1.5
1
2.5
0.1
200
50
.05
4
0
-20
+20
3
OFF
6
GAIN
LEVEL
THRESHOLD
dB
+10
1
2
4
6
9
12
15
18
21
24
27
30
+6
+3
0
-3
-6
-10
-20
-30
-30
-20
0
-40
+20
-10
RATIO
CH 2
CH 1
MANUAL
AUTO
M1
msec
RELEASE
Sec
OUTPUT
dB
0.5
OUT
IN
COMPRESSOR/LIMITER
ENHANCER
OFF
THRESHOLD
INAUDIBLE
+
-
dB
+10
0
-50
-35
-10
-20
EXPANDER/GATE
8
1.5
1
2.5
0.1
200
50
.05
4
0
-20
+20
3
OFF
6
GAIN
LEVEL
MODE
AUDIO OUTPUT
AUDIO INPUT
AC DEVICE CONNECTIONS
The GIG-MASTER has an AC power outlet on the rear panel to provide power to a connecting device.
NOTE: A device with a power consumption rating over 200W should not be connected as that exceeds the allowable power feed.
Doing so may cause serious damage to both devices and may void your warranty.
CONNECTING EXTERNAL SPEAKERS
The GIG-MASTER has a set of speaker connectors for connection to external speakers. Remember that only
speakers with an impedance rating of 8 ohms should be connected.
To connect speakers, first unlock the plastic fasteners on each speaker connector by pushing downward on
them. Then strip approximately a 1 /2 “ of insulation from the speaker wire ends and twist the strands so
that they can easily slide through the holes. Once a wire is inserted, lock them in place with the fasteners by
pushing upward on them. It is easy to over-insert a wire into a speaker connector so that the insulation is
inserted as well. To ensure this doesn’t happen, only insert the wires to the point where you can still see the
edge of the insulation.
*Set to EXT for
External Speaker
Output
L
R
SPEAKER 8
INT
EXT
Speacker Selector
