background image

UF-216CC water Filtration system

8

A.J. Antunes & Co.

P/N 1011135 Rev. A 03/12

unpacking

  1.  Remove the system and all packing materials 

from the shipping carton.

  2.  Remove all packing materials and protective  

coverings from the system

  3.  Remove the information packet. To prevent any 

delay in obtaining warranty coverage, fill out and 

mail the warranty card.

nOte: If any parts are damaged, contact a.J. 

antunes & co. ImmeDIately at 1-800-253-2991 or 

1-630-784-1000.

InstallatIOn

plumbInG

nOte: this unit is designed to use tap water not to 

exceed 100°f (38°c) or 100 psig (690 kpa).

The UF-216CC system uses the following connections 

(Figure 1):

 

•  Water Inlet  

 

 

1/2” NPT

 

•  Permeate (Product Water) 

1/2” NPT

 

•  Drain   

 

 

1/2” NPT

When making a plumbing connection to the system, 

remember to use a back-up wrench on the supporting 

plumbing.  Always use a good quality, approved pipe 

sealant or thread seal tape on pipe threads.  Be careful 

not to get the pipe sealant inside the pipe when making 

the connections.  

Do NOT over tighten the connections.  It is recom

-

mended that plastic fittings be used when connecting to 

the plastic connections of the system.  This will reduce 

the possibility of  cracking the connections due to over-

tightening.  
If soldered plumbing is used, do NOT apply heat to, 

or near, the filtration system.  The use of union (O-ring 

seal) connections is highly recommended for ease of 

installation and future servicing.

cautIOn

this equipment is to be installed to comply with 

the basic plumbing code of the building Officials 

and code administrators, Inc. (bOca) and the 

food service sanitation manual of the food and 

Drug administration (fDa).

cautIOn

water pressure must not exceed 100 psig (690 

kpa).  to reduce water pressure, install a water 

pressure regulator and set water pressure to suit 

application.  note that the trans membrane pres-

sure must not exceed 45 psi (310 kpa).

equipment setup

General

When placing the unit into service, pay attention to the 

following guidelines:

  •  Do NOT immerse cord or plug in water.

  •  Keep cord away from heated surfaces.

suGGesteD tOOls anD supplIes fOr InstallatIOn

The following tools and supplies are suggested to make 

the installation easier:

•  Screwdriver

 

•  Drill with bits

 

•  Tape measure

 

•  Pipe wrenches

 

•  Adjustable wrenches

 

•  level

 

•  Two gallon bucket

 

•  Pipe dope or thread seal tape

 

•  Fresh 5 1/4% liquid chlorine  

 bleach

electrIcal

Ensure that the line voltage corresponds to the stated 

voltage on the units specification label. Make sure that 

the plug on the power cord from the system and the 

outlet match. For proper operation, and to ensure the 

highest quality water from the system, make sure that 

the system is not connected to a switched electrical 

outlet.

ImpOrtant

commonwealth of massachusetts plumbing code 

248 cmr shall be adhered to. the use of saddle 

valves are not permitted, please consult your local 

plumber.

Summary of Contents for UF-216CC





















Reviews: