Vivotek IP8362 User Manual Download

Page: 84 / 185

VIVOTEK

84 - User's Manual

Custom command

Custom Camera (scanner)

is selected as the PTZ driver,

the

Preset Position

and

PTZ Control

Panel

on the main page will be disabled. You will need to

configure command buttons to control the PTZ

scanner. Click

Custom Command

to open the Custom Command page to set the commands in the

Control Settings session. Please refer to your PTZ scanner user's manual to enter the commands in the

following fields. Click

Save

to enable the settings and click

Close

to exit the page.

NOTE

►If you select DynaDome/SmartDOME, Lilin PIH-7x00, or Pelco D protocol as the PTZ driver, the

Control Settings column will not be displayed.

►For all PTZ drivers, a total of five additional command buttons can be configured.

►The command buttons will be displayed on the main page:

2010/12/10 17:08:56

Summary of Contents for IP8362


























































































































































































Search results

Summary of Contents for IP8362

Reviews:

Related manuals for IP8362

Brands by name

Popular brands

Vivotek IP8362, User Manual

Search results

Summary of Contents for IP8362

Reviews:

Related manuals for IP8362

Brands by name

Popular brands