Vivotek IP8362 User Manual Download

Page: 135 / 185

VIVOTEK

User's Manual - 135

7.9 Video input preview

The temporary settings for video preview
Group: videoinpreview

NAME

VALUE

SECURITY
(get/set)

DESCRIPTION

exposuremode

auto,fixed

4/4

Exposure mode

minexposure

1~32000

4/4

Minimum exposure time.

maxexposure

1~32000

4/4

Maximum exposure time.

exposurelevel

0~12

4/4

Exposure level

enableblc

4/4

Enable backlight compensation.

enablewdr <boolean>

4/4 Enable/disable

wield dynamic range. (not used in

IP8362)

irismode

fixed, indoor, outdoor

4/4

Video Iris mode for DC Iris.

wdrc_mode

0~3

4/4

WDR enhanced.
0: off
1: auto
2: always on
3: keep current value

wdrc_strength

0~2

4/4

WDR enhanced.
0: low
1: medium
2: high

agc

0,1,2

4/4

Set auto gain control to normal level or MAX level.
0->2x,
1->4x,
2->8x
(not used in IP8362)

agcmode

auto,fixed

4/4

Set auto gain control mode.

maxgain

0~100

4/4

Manual set maximum gain value.

mingain

0~100

4/4

Manual set minimum gain value.

autoiris

4/4

Enable auto Iris.
(not used in IP8362)

Summary of Contents for IP8362


























































































































































































Search results

Summary of Contents for IP8362

Reviews:

Related manuals for IP8362

Brands by name

Popular brands

Vivotek IP8362, User Manual

Search results

Summary of Contents for IP8362

Reviews:

Related manuals for IP8362

Brands by name

Popular brands