VivoLink VLSC242 User Manual Download Page 46

Page: 46 / 58

4x2 HDMI 2.0 Seamless Matrix Switcher

2.HDMI output (Loop)

2.HDBT output



The “

[command]

” represents the specific command from the table below.



Control the input source:

Command

Description

Command Example and Feedback

#SEND_CECCMD
[port]:00

Confirm operation (Enter).

#SEND_CECCMD 03:00

[CEC]: blue ray OK.

#SEND_CECCMD
[port]:01

UP.

#SEND_CECCMD 03:01
[CEC]: blue ray up.

#SEND_CECCMD
[port]:02

DOWN.

#SEND_CECCMD 03:02

[CEC]: blue ray down.

#SEND_CECCMD
[port]:03

LEFT.

#SEND_CECCMD 03:03

[CEC]: blue ray left.

#SEND_CECCMD
[port]:04

RIGHT.

#SEND_CECCMD 03:04
[CEC]: blue ray right.

#SEND_CECCMD
[port]:09

Back to submenu.

#SEND_CECCMD 03:09
[CEC]: blue ray menu.

#SEND_CECCMD
[port]:0D

Exit.

#SEND_CECCMD 03:0D
[CEC]: blue ray Exit.

#SEND_CECCMD
[port]:41

Volume up.

#SEND_CECCMD 03:41
[CEC]: blue ray Volume Up.

#SEND_CECCMD
[port]:42

Volume down.

#SEND_CECCMD 03:42
[CEC]: blue ray Volume Down

#SEND_CECCMD
[port]:44

Play.

#SEND_CECCMD 03:44
[CEC]: blue ray play.

#SEND_CECCMD
[port]:45

Stop.

#SEND_CECCMD 03:45
[CEC]: blue ray stop.

#SEND_CECCMD
[port]:46

Pause.

#SEND_CECCMD 03:46
[CEC]: blue ray pause.

#SEND_CECCMD
[port]:48

Rewind

#SEND_CECCMD 03:48
[CEC]: blue ray backward.

#SEND_CECCMD
[port]:49

Fast forward.

#SEND_CECCMD 03:49
[CEC]: blue ray forward.

#SEND_CECCMD
[port]:4B

Forward.

#SEND_CECCMD 03:4B
[CEC]: blue ray skid forward.

#SEND_CECCMD

Backward.

#SEND_CECCMD 03:4C

Summary of Contents for VLSC242


























































Search results

Summary of Contents for VLSC242

Reviews:

VivoLink VLSC242, User Manual, Page: 46 / 58

Search results

Summary of Contents for VLSC242

Reviews: