VivoLink VLSC242 User Manual Download Page 16

Page: 16 / 58

4x2 HDMI 2.0 Seamless Matrix Switcher

4. System Connection

4.1 Usage Precaution



Make sure all components and accessories included before installation.



System should be installed in a clean environment with proper temperature and
humidity.



All of the power switches, plugs, sockets, and power cords should be insulated and
safe.



All devices should be connected before power on.

4.2 System Diagram

The following diagram illustrates the typical input and output connection of the
switcher:

4.3 RS232 Connection

The switcher supports RS232 local control and RS232 pass-through, and the receiver
supports RS232 pass-through. There are five modes of RS232 control connection as
below:

①

Connect PC to the RS232 port of switcher to control the switcher by sending

RS232 commands. Please refer to the chapter

8.RS232 Control

for more details.

②

Connect PC to the RS232 port of receiver to control the switcher by sending

RS232 commands.

DC 24V

1.HDMI

2.HDMI

3.HDMI

4.USB-C

1.HDMI

Phantom (48V)

OFF

MIC

FIRMWARE

RS232

2.HDBT

AUDIO

SPDIF

IR EYE

IR IN

IR OUT

OUTPUTS

AUDIO INPUTS

CONTROL

2.HDMI

MIX

AUDIO

LINK

HDCP

Game Console

Laptop

MacBooK

RS232

STEREO

BRIDGE

MONO

MIC

LINE

48V

MIC

INPUTS

Audio Player

Speaker

Amplifier

Soundbar

4K TV

Projector

HDMI 2.0 Receiver

IR Receiver

Remote

Central

Control System

HDMI:

Control:

Ethernet:

Audio:

HDBaseT:

USB-C:

Blu-Ray

4K TV

Wireless Router

iPad

MIC

Summary of Contents for VLSC242


























































Search results

Summary of Contents for VLSC242

Reviews:

VivoLink VLSC242, User Manual, Page: 16 / 58

Search results

Summary of Contents for VLSC242

Reviews: