background image

HDBaseT Transceiver Set

 

 

Preface 

Read this user manual carefully before using this product. Pictures shown in this manual 
is for reference only, different model and specifications are subject to real product. 

This manual is only for operation instruction only, not for any maintenance usage.   

 

Trademarks 

Product model and logo are trademarks. Any other trademarks mentioned in this manual 
are acknowledged as the properties of the trademark owner. No part of this publication 
may be copied or reproduced without the prior written consent. 

 

FCC Statement 

This equipment generates, uses and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause harmful interference 
to radio communications. It has been tested and found to comply with the limits for a 
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed 
to provide reasonable protection against harmful interference in a commercial 
installation. 

Operation of this equipment in a residential area is likely to cause interference, in which 
case the user at their own expense will be required to take whatever measures may be 
necessary to correct the interference. 

Any changes or modifications not expressly approved by the manufacture would void 
the user’s authority to operate the equipment. 

         

           

     

Summary of Contents for VL120017





























Reviews: