manualshive.com logo in svg

Vivato VA4200, User Manual, Page: 54 / 181

Share
Download
Vivato VA4200 User Manual Download Page 54

Copyright © 2004-2005, Vivato, Inc.

54

Fragmentation Threshold

Specify an even number between 256 and 2,346 to set the frame size thresh-
old in bytes.

The 

fragmentation threshold

 is a way of limiting the size of packets (frames) 

transmitted over the network. If a packet exceeds the fragmentation threshold 
set here, the fragmentation function will be activated and the packet will be 
sent as multiple 802.11 frames.

If the packet being transmitted is equal to or less than the threshold, fragmen-
tation will not be used.

Setting the threshold to the largest value (2,346 bytes) effectively disables frag-
mentation.

Fragmentation involves more overhead because of the extra work of dividing 
up and reassembling of frames it requires, and because it increases message 
traffic on the network. However, fragmentation can help 

improve

 network per-

formance and reliability if properly configured.

Sending smaller frames (by using lower fragmentation threshold) may help 
with some interference problems; for example, with microwave ovens.

By default, fragmentation is off. We recommend not using fragmentation unless 
you suspect radio interference. The additional headers applied to each frag-
ment increase the overhead on the network and can greatly reduce throughput.

RTS Threshold

Specify an 

RTS Threshold

 value, in bytes, between 0 and 2347.

The RTS threshold specifies the frame size before a request to send (

RTS

) 

transmission is performed. This helps control traffic flow through the AP/Bridge, 
especially one with a lot of clients.

If you specify a low threshold value, RTS packets will be sent more frequently. 
This will consume more bandwidth and reduce the throughput of the packet.

On the other hand, sending more RTS packets can help the network recover 
from interference or collisions which might occur on a busy network, or on a 
network experiencing electromagnetic interference.

ICCF

Select 

Enable

 or 

Disable

. 

When enabled, inter-client communication filtering (ICCF) prevents wireless 
clients associated on this radio from being able to communicate directly with 
other clients associating on this radio or on another radio on this AP/Bridge.

Short Preamble

Select 

Enable

 or 

Disable

. 

When enabled, the short preamble uses fewer synchronization and CRC bits in 
order to allow additional data throughput. All 802.11g clients should support 
using a short preamble. However, 802.11b clients are not required to support 
short preamble operation and therefore using a short preamble may not work 
with them.

Max Stations

Specify the maximum number of stations allowed to access this AP/Bridge at 
any one time.

You can enter a value between 0 and 2007.

Field(Continued)

Description(Continued)

Summary of Contents for VA4200






















































































































































































Reviews:

No comments