Vitek VT-TSP8 Manual Download Page 61

Page: 61 / 64

DETAILED SPECIFIC

OPTIONAL MOUNTS

VT-TSP8 - Body Temperature Detecting Panel

Image Sensor

Display Screen

Temperature Measuring Range

Temperature Measuring Distance

Face Recognition Distance

Storage

Control Interface

Recognition Mode / Duration

Face Capacity / Accuracy

WDR

Fill-in Light

Smart Features

Audio

Network Interface

Alarm Input/Output

Wiegand Interface

RS485

Door Lock Output

SD Card Interface

USB Interface

Button Features

Power

Power Consumption

Protection

Operating Environment

Dimensions w/ Sensor

1/2.7” 2MP dual-lens, f=3.97mm @ F1.6

8-inch 1280x800 LCD with 500:1 Contrast Ratio

32~212°F with ± 0.3°F Accuracy

12” ~ 18” (0.3m~0.5m)

1’ ~ 6.5’ (0.3m-2m)

8Gb DDR3 +16GB EMMC

Embedded Linux

12C

Face: 1:N /

≤

0.5 s per person

20,000 / 99.70%

120Db

Soft white light, IR light with up to 10’ (3m) Distance

Screen Wake Up, Light Adjustment, Snapshot

Two-Way Audio: 1-CH built-in Mic w/Built-in Speaker*

10/100Mbps self-adaptive Ethernet port x1

2-CH (Input) / 2-CH (Output)

Wiegand input/output (26/34)

RS485x1 (half duplex)

Relay output, NO/NC (optional), delay setting supported

1 MicroSD Card Slot (up to 256GB)

USB x1

Anti-Tamper Interface, Exit. Reset

12V @2A

<12W

IP66, Surge Protection and Voltage Transient Protection

50°F ~ 95°F

11.88” x 5.47” x 1.35” (301.8 x 138.6 x 34.2mm)

*Please research local, state and federal laws regarding the implementation of audio surveillance.

Summary of Contents for VT-TSP8

































































Search results

Summary of Contents for VT-TSP8

Reviews:

Brands by name

Popular brands

Vitek VT-TSP8, Manual

Search results

Summary of Contents for VT-TSP8

Reviews:

Brands by name

Popular brands