manualshive.com logo in svg

Vitek VT-TSP8, Manual

Share
Download
Vitek VT-TSP8 Manual Download Page 24

 

19 

 

 
When the captured face is not added to the face database or the similarity is lower than the pre-
defined value, it will display “Match Failure” and the box will turn red.   
If the mask detection and “Trigger Audio Alarm” are selected, warning voice will be heard if 
no mask is detected. 

 

4.2 Live View via Web 

After logging in, the following window will be shown. 
In this interface you will see the captured face, match result and body temperature. 

 

 

The following table is the instructions of the icons on the live view interface. 
 

Icon 

Description 

Icon 

Description 

 

Original size   

 

Start/stop local recording   

 

Fit correct scale   

 

Zoom in   

 

Auto (fill the window) 

 

Zoom out   

 

Full screen   

 

SD card recording indicator

 

 

Start/stop live view   

 

Sensor alarm indicator

 

 

Start/stop two-way audio   

 

Motion alarm indicator   

 

Enable/disable audio   

 

Face detection indicator 

 

Snapshot

 

 

Face match

 

 

Those smart alarm indicators will flash only when the TSD Panel supports those functions and 

Summary of Contents for VT-TSP8

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands